background image

925-0322 Rev C

0415

Solids Flow Detect Model FD-2000

Solids Flow Detect Model FD-2000

LIMITED WARRANTY

Garner Industries warrants this product against defects in material and workman-
ship for two (2) years according to the following terms;

1.)  This warranty extends to the original purchaser only and commences on the 

date of original purchase.

2.)  Garner Industries sole obligation under said warranty is to repair, or at its option 

replace the defective parts.  The buyer shall have no other remedy. All special, 

incidental and consequential damages are excluded. The buyer must deliver 

the product under warranty prepaid to the factory. Garner Industries obligation 

is limited to the cost of material and labor to repair or replace, and does not 

include transportation expenses.

3.)  This warranty shall be voided, in our sole judgment, by alterations of equipment 

except by Garner Industries, or tampering with, improper installation or mainte

-

nance, accident or misuse, or act of God. This warranty expressly excludes all 

damage to the product resulting from careless or neglectful packaging or trans-

portation. The warranty does not extend to repairs made necessary by normal 

wear.

4.)  This warranty is in lieu of all other warranties, expressed or implied including 

any implied warranties or merchantability or fitness for particular purpose. No 

employee, agent, franchise dealer or other person is authorized to give any 

warranties of any nature on behalf of Garner Industries.

5)

Garner Industries shall in no event be responsible for any warranty work done

without first obtaining Garner Industries written consent.

6)

Except as provided herein, Garner Industries shall have no liability, loss or

damage caused or alleged to be caused directly or indirectly by this equipment.

7)

This warranty gives the buyer specific legal rights, and you may also have other

rights which vary from state to state.

8)

Содержание FD-2000

















Отзывы: