manualshive.com logo in svg

Binks PT-418-CE, Инструкция по эксплуатации, Страница: 10 / 12

Поделиться
Скачать
Binks PT-418-CE Скачать руководство пользователя страница 10

Page 10 

© ITW Inc 2007 

Parts list for PT-427-CE, PT-418-CE, 

PT-419-CE & PT-428-CE 

Fig 8 

Ref. 
No. 

Replacement Part 
No.  

Description 

Individual 
Parts Req. 

* 35 

 

PT-410 

83C 

Air Motor Assembly 

1 

QMS-455 

83Z 

36 

 

QS-190 

83C 

End Cap 

1 

PT-65 

83Z 

* 37  ——– 

 

End Cap Gasket 

1 

38  PT-58 

 

Bearing 

1 

39  ——– 

 

Screw (1/4”-28 x 1/2”) 

12 

* 40  ——– 

 

Front Plate 

1 

* 41  PT-59-1-K10 

 

End Plate Gasket 

2 

42  QS-189-1-K10   

Dowel Pin (Kit of 10) 

4 

•

     43  ——– 

 

Body 

1 

* 44  ——– 

 

Vane 

4 

•   

**45 

——– 

 

Rotor Assembly 

1 

•

     46  ——– 

 

End Plate 

1 

47  PT-56 

 

Shaft Seal 

1 

48  PT-50 

 

Air Motor Adaptor 

1 

49  ——– 

 

Set Screw (1/4”-20 x 1/4”) 

4 

50  KK-5041 

 

Seal Assembly 

1 

QMG-441 

83C  Shaft Coupling Kit (includes 

No 49) 

1 

QMS-453 

83Z 

52  SSG-8096-K5   

“O” Ring (Kit of 5) 

1 

53  PT-70 

 

Adaptor Nut 

1 

54  QMG-56 

83C  Shaft 

1 

 

QMS-73 

83Z 

Shaft SS 

1 

55  QMS-448-CE 

 

Propeller Assy 

1 

56  ——– 

 

Propeller 

1 

56A  ——– 

 

Set Screw (1/4”-20 x 3/8” 
S.S) 

1 

57  350-401 

 

Muffler Assembly 

1 

58  ——– 

 

Body 

1 

♦

    59  ——– 

 

Screen 

2 

♦  

* 60  ——– 

 

Felt 

1 

61  ——– 

 

Cap 

1 

# 62 

 

PT-428-CE 

83C 

Agitator Shaft Kit 

 

1 

 

PT-419-CE 

83Z 

66  

PT-418-CE 

83C 

Air Motor & Adaptor 

 

1 

PT-427-CE 

83Z 

* Parts included in KK-5001-1 Air Motor Repair Kit 

•

 

 Parts included in (35) PT-410/QMS-455 Air Motor Assembly 

♦

 Ref. No. (59) 2 ea. & Ref. No. (60) 4 ea. Included in KK-5006 Strainer 

Screen & Felt kit 

** Not available separately, order (35) PT-410/QMS-455 

51 

 

Содержание PT-418-CE













Отзывы:

Нет отзывов