background image

 

 

 

 

 

 

KBF-S (E6) 08/2018

 

page 69/88 

 

23.  Troubleshooting 

Fault description 

Possible cause 

Required measures  

General 

Chamber without function. 

No power supply. 

Check connection to power sup-
ply. 

Wrong voltage. 

Check power supply for correct 
voltage (chap. 4.3). 

Chamber fuse has responded. 

Check chamber fuse and replace 
it if appropriate. If it responds 
again, contact BINDER service. 

Controller defective. 

Contact BINDER service. 

Nominal temperature exceeded 
by 10°C due to chamber failure. 
Over temperature protective de-
vice (class 1) responds. 

Heating 

Chamber heating permanently, 
set-point not maintained. 

Controller defective. 

Contact BINDER service. 

Semiconductor relay defective. 

Controller not well adjusted, or 
adjustment interval exceeded. 

Calibrate and adjust controller. 

Chamber doesn’t heat up. 

Pt 100 sensor defective. 

Contact BINDER service. 

Heating element defective. 

Semiconductor relay defective 

Chamber doesn’t heat up when 
turned on.  
Safety controller responds. 

Inner chamber temperature has 
reached the safety controller 
value. Safety controller set too 
low. 

Acknowledge the alarm on the 
controller. Check temperature 
setpoint setting. If appropriate, 
select suitable safety controller 
value (chap. 10.2). 

Safety controller (chap. 10.2) 
defective. 

Contact BINDER service. 

Refrigerating performance 

Low or no refrigerating perfor-
mance. 

Ambient temperature above 
25 °C / 

77 °F

 (chap.3.4).  

Select cooler place of installation.  

Combination of tempera-
ture/humidity values not in the 
optimum range (see temperature 
humidity diagram, Figure 18). 

Select combination of tempera-
ture/humidity values in the opti-
mum range (chap. 18). 

Compressor not turned on. 

Contact BINDER service. 

Electro-valves defective. 

No or not enough refrigerant. 

Too much external heat load. 

Reduce heat load. 

Humidity 

Humidity fluctuation: 
Control accuracy of +/- 3 % r.h. is 
not reached. 

Door gasket defective. 

Replace door gasket. 

Door opened very frequently. 

Open doors less frequently. 

Humidity fluctuation, together 
with temperature fluctuation > 1 
°C with a set-point approx. 3 °C 
above ambient temperature. 

Place of installation too hot. 

Select cooler place of installation 
or contact BINDER service. 

No or low dehumidification. 

Capillary tube blocked 

Contact BINDER service. 

Not enough refrigerant. 

Humidity control turned off. 

Turn on humidity control (chap. 
8). 

Содержание KBF-S 240


























































































Отзывы:

Похожие инструкции для KBF-S 240