Channel Number. Changes
from 1 to 8 as selected by the
user.
Displayed when the Key Lock feature is activated.
Displays the current Speaker volume level.
Shown when the Scan feature is turned ON.
Displays the current Battery
charge level.
Shown when the unit is in VOX(voice activated) mode
USER GUIDE
Speaker
Displayed when transmitting a signal.
Displayed when receiving a signal.
symbols.
Mic (Microphone)
CALL button
-
Press to send a
ringing tone to
other PMR units.
PTT (PUSH to
TALK) button
-
Press and hold
to transmit.
Antenna
LCD Screen
-
Displays the
current channel
selection and
other radio
MENU Button
-
Press to program
the PMR settings.
(UP )/ (DOWN)
buttons - Press to
change channels,
volume, and to
select settings
during programming.
(Power) button
-
Press and hold to
turn the PMR unit
ON or OFF
.
1.LCD Screen
1.LCD Screen
VOX
Private mobile radio with twin charger
Terrain150
2.3 Installing the Batteries
2.3 Installing the Batteries
Caution:
Caution: Observe
Observe the
the proper
proper battery
battery polarity
polarity orientation
orientation when
when
installing
installing batteries.
batteries. Incorrect
Incorrect positioning
positioning can
can damage
damage both
both the
the
batteries
batteries and
and the
the unit.
unit.
2. Installation
2. Installation
2.1 Removing the Belt Clip
2.1 Removing the Belt Clip
a.
a. Pull the Belt Clip Latch
away from the PMR.
b.
b. While pulling the Belt
Clip Latch, push up
the Belt Clip as
shown in Figure 1.
Figure 1
Figure 2
2.2 Installing the Belt
2.2 Installing the Belt
Clip
Clip
a.
a. Slide the Belt Clip into
the slot as shown in
Figure 2.
b.
b. A “click” indicates the
Belt Clip is locked into
position.
a.
a. Slide down the Battery Compartment Cover.
b.
b. Insert 3 AAA size Ni-Mh
by following the
polarity marking inside the Battery Compartment as shown in
Figure 3.
c.
c. Replace the Battery Compartment Cover. See Figure 4.
Figure 3
Figure 4
Belt clip
latch
Rechargeable batteries.
Notes:
Notes:
Use only same type and make of batteries on the PMR units.
The PMR units have a built-in Power Saver (PS) for maximum
battery life, but when not in use, turn the units OFF to
conserve battery power.
Remove the batteries if the units will not be used for a long
period of time.
2.4 Charging the batteries
insert the DC JACK
of the 7.5V DC/200mA adaptor
into the charge jack on topof the unit
Plug the mains adaptor into
a 230V AC,50Hz main socket
with the switch on the socket
set to OFF.Then switch ON
the main socket.
Use only batteries listed in the user instruction
Jiang Su CEL Co.,Ltd.,3X1.2V AAA size/600mAh Ni-MH
Rechargeable batteries.
The PMR must be charged using the mains adaptor provided. Using any
other adaptor will result in non-compliance
P
with EN60950-1 and will
P
invalidate any approval/warranty for this product.
During Charging, the battery level indicator icon will start flashing on the
display in both off mode and PMR on mode. During
During
During
During charging
charging
charging
charging mode,
mode,
mode,
mode, the PMR
the PMR
the PMR
the PMR
transmit
transmit
transmit
transmit and receive
and receive
and receive
and receive is disabled.
is disabled.
is disabled.
is disabled.
It takes about 10 hours to recharge the battery fully if they've
become completely run down. New battery take up to 12 hours to
charge fully.
Important
Important
Important
Important _ read these Safety Warning before you charge the batteries
• When Charging the handset , use only the rechargeable batteries
supplied with the PMR. •
• Don't try to recharge non-rechargeable batteries.
• Make sure the battery compartment cover is securely locked in place
when you are charging the batteries.
• Dispose of used batteries safely and in a way that will not harm the
environment - Never try to burn them or put them anywhere, they could get
burnt or punctured....
• Don't leave dead batteries in your handset. They might leak if you do.
Battery meter
The battery meter is located in the left corner of the LCD panel. It looks
like a battery with three bars inside. These indicate the amount of
power available. As the power is used the bars will disappear. When the
battery level reaches its minimum level, the handset will emit two beep
tones and automatically turn OFF the power.
Use only power supply listed in the user Instruction.
PMR:CSEC brand model-CSD0750200G adaptor
Charger:CSEC brand model-CSD0900200G adaptor
3. Operation
3. Operation
3.1 Turning the Unit ON/OFF
3.1 Turning the Unit ON/OFF
3.2 Adjusting the Speaker volume
3.2 Adjusting the Speaker volume
There are 8 volume levels, the current speaker volume
level is displayed on the LCD Screen.
To adjust the speaker volume level, press the (UP)
button to increase, or press the (DOWN) button to
decrease. The LCD Screen will display the speaker volume
icon bars ascending, or descending respectively.
3.3 Receiving a Call
3.3 Receiving a Call
The unit is continuously in Receive mode when the
unit is turned ON and not transmitting. When a signal is
received on the current channel, the receive signal icon
“ ” will be displayed on the LCD Screen.
3.4 Transmitting (sending)
3.4 Transmitting (sending)
Press and hold the PTT (Push to Talk) button to transmit
your voice. The transmit signal icon “ ” will display on
the LCD Screen.
Hold the unit in a vertical position with the Mic
(Microphone) 5 cm away from the mouth. While holding
the PTT button, speak into the mic (microphone) in a
normal tone of voice.
Release the PTT button when you have finished
transmitting.
To Turn ON;
To Turn ON;
a.
a. Press and hold the (Power) button. A special “beep"
sound will be heard. The LCD Screen will be illuminated by
an orange light for several seconds, and will display the
current channel.
To switch OFF;
To switch OFF;
b.
b. Press and hold the (Power) button. A special “beep"
sound will be heard and the LCD Screen will turn blank.
a.
a.
b.
b.
c.
c.
Important:
Important:
In order for other people to receive your transmission, they must
also be on the same channel that you are currently using. Refer
to the "Changing Channel" section for more information.
When the PTT and/or CALL buttons are continuously pressed,
your PMR cannot receive any transmissions.
The PMR has 8 available channels. To change channels, in
normal mode;
a.
a. Press the MENU button, the Channel icon “ ” on the LCD
Screen will start blinking.
b.
b. While the Channel icon is blinking, press the (UP) or
(DOWN) button to select the desired channel. The channel
changes from 1 to 8, or from 8 to 1.
c.
c. Press the MENU button to confirm your selection and
return to the normal mode.
Battery life
The PMR has a built in power saver feature to make the batteries
last longer. But when you are not using the handset, it's better to
switch it off to save the battery power.
With the PMR in normal mode, press and release the CALL
button. The unit will transmit a 2-second page tone to the
other unit/s set with the same channel within transmitting
range .
a.
a.
You can use the CALL button to send a tone to other users on
the same channel. To activate this feature;
3.6 Calling (Paging) Tone
3.6 Calling (Paging) Tone
To turn the Key-Tone ON or OFF
Press the
MENU
button three times.The “ ” icons flashes
on the display.
Press the
UP
buttons to enable or
DOWN
to disable
the key tone feature
Press the
PTT
button to confirm your setting.
To turn VOX mode ON and OFF:
Press the
MENU
button five times
VOX
icon is displayed and OF flashes on the LCD panel.
Press the
UP
button activate the vox feature.
Press
Down
to turned off the VOX
Press the
PTT
button to confirm the setting.
As long as the handset is in VOX mode,VOX is shown
steadily on the display.
This feature allows the handset to sound a confirmation tone
whenever keys are pressed
3.7 Key tone ON/OFF setting
3.7 Key tone ON/OFF setting
ON
ro
3.8 Roger Beep
3.8 Roger Beep
The Roger Beep is a tone which is automatically transmitted
whenever the PTT button is released. This alerts the
receiving party that you have ended the transmission, and
you are now in receive mode.
3.9
3.9
VOX (voice activated transmission) mode
In VOX mode your handset will transmit whenever it detects your
voice (or other noise) without the PTT button having to be pressed.
3.5 Changing the channels
3.5 Changing the channels
3.5 Changing the channels
Setting Call-Ring tones
Press
MENU
button for
Twice
times, the
unit will enter to
CA
Call-Ring setting mode.
The LCD will display
1
while 1
is flashing.
Press the or button to change the Call-Ring tone.
(5 different tones)
,the different Call-Ring tone can be heard
during changing.
Press the
PTT
button to confirm your setting after you select
your desired Call-Tone.
DOWN
Setting Call-Ring off
If you don't want to hear the call tone, you can set the Call-Ring
mode to OFF. In this stage, you can send the call-ring(default call-
ring number 1)to other party but the Terrain 150 you held will
not sound.
UP
Press
MENU
button for
Twice
times,
the unit will enter to
Call-Ring setting mode.
CA
Press the or button until display
OF
on the LCD panel.
Press the
button to confirm your setting.
PTT
UP DOWN
Binatone Help Line - 0845 345 9677
Binatone Help Line - 0845 345 9677
Setting Call-Ring off
Setting Call-Ring tones