Billy Goat MV601SPEEU, Руководство пользователя

Страница: 5 / 24

MVSPEU Owner’s Manual
Part No 840286 5 840286_B_HI
ASSEMBLY INSTRUCTIONS
Your BILLY GOAT
®
MV Vacuum was shipped in one carton, completely assembled except for the Hood/Upper Handle Assembly.
Mounting hardware for the Hood/Upper Handle Assembly is temporarily installed on the lower handle and the Housing Assembly.
PARTS BAG HARDWARE
DISCONNECT spark plug wire before assembling unit.
1st
ITEM NO. PART NO. DESCRIPTON QTY
139 840061 ROD LIFT NOZZLE DOOR 1
150 900407 TY- WRAP 2
152 8171003 WASHER 5/16" FLAT ZP 4
153 8160002 NUT LOCK 5/16"-18 2
158 8041006 SCREWCAP 1/4"-20 X 1" ZP 2
159 8041031 SCREWCAP 5/16" X 1 3/4" ZP 2
160 8171004 WASHER 3/8 FLAT 4
161 8172007 WASHER 1/4" SAE ZP 5
164 400886 ROD END BALL JOINT 3/8" NF 2
165 8041052 SCREWCAP 3/8"-16 X 1 1/2" ZP 1
166 8160003 NUT LOCK 3/8"-16 2
167 8041056 SCREWCAP 3/8"-16 X 2 1/2" ZP 1
170 8041004 SCREWCAP 1/4"-20 X 3/4" HCS ZP 1
171 8172019 WASHER FENDER 1/4" ZP 2
173 840071 NUT ACORN 1/4"-20 2
READ all safety instructions before assembling unit.
TAKE CAUTION when removing the unit from the box. The Hood/Upper Handle Assembly is attached to the
unit by cables.
Boxing Parts Checklist
Honda 6.5 Engine
B&S 6 Engine
Parts bag P/N-840187
Ty-wraps (2 ea)
PARTS BAG & LITERATURE ASSY
Warranty card P/N- 400972, Owner’s Manual P/N-840245, General Safety and Warnings Manual P/N-100294, Declaration of
Conformity P/N-840204
Fig . 1
1. Attach hood assembly to the housing then hold in place during step 2.
NOTE: be sure all cables are routed on the underside of the hood and
housing. (See Fig . 1)
2. Install (item 170) center bolt first when aligned with a nut on the housing.
(See Fig . 2)
3. Attach rest of hood assembly to the housing using corresponding
hardware. NOTE: You will have to insert the bolt/washer from the inside
by reaching through the hood. (See Fig . 2)
4. Attach upper handle brace to lower handle using corresponding hardware.
Then repeat this step on the other side
.
(See Fig . 3 next page)
5. Attach rod end (item 164) to the nozzle door rod then secure in place by
tightening jam nut. (See Fig . 4 next page)
6. Attach nozzle door rod to the nozzle door using corresponding hardware.
NOTE: It is easier to do this with nozzle door closed.
7. Attach rod end to rod (See Fig . 5 next page).
8. Attach nozzle door rod to the lever with nozzle door closed and lever in
hose kit position. NOTE: Check to see that the nozzle door opens and
closes all the way (see page 15). Tighten or loosen the rod end (item 164)
for any adjustments. (See Fig . 4 and 5 next page)
9. Install cable ty wraps.
10. Reconnect spark plug wire.
11. Attach the bag. (See
Fig
. 7)
Fig . 2
NOT
FOR
REPRODUCTION