background image

 

 

Part No 500264 

F091506B 

BC2402 Series Brush Cutter Owner’s Manual 

SOUND DATA 
 

SOUND LEVEL 93 Dba at Operator’s position 

 

Sound tests were conducted in accordance with 2000/14/EEC and were performed on 2/21/2002 under the 
conditions listed below. 

 

Sound power level listed is the highest value for any model covered in this manual. Please refer to 
serial plate on the unit for the sound power level for your model.

 

 

General Conditions:   

Sunny 

Temperature:  

80

o

F (25

o

C) 

Wind Speed: 

 

2.0 mph (3.2 kph) 

Wind Direction: 

 

South 

Humidity:  

63.5% 

Barometric Pressure: 

29.98” Hg (761mm Hg) 

 
 
 
 
 
 
 
 

VIBRATION DATA 
 

VIBRATION LEVEL .5g (4.87 m/s

2

Vibration levels at the operator’s handles were measured in the vertical, lateral and longitudinal directions using 
calibrated vibration test equipment. Tests were performed on 5/19/1995 under the conditions listed below. 
 
General Conditions: 

Sunny 

Temperature: 89

o

F (31.7

o

C) 

Wind Speed: 

6.1 mph (9.9 kph) 

Wind Direction: 

West 

Humidity: 49.7% 
Barometric Pressure: 

29.88” Hg (101.19 kPa) 

 
 
 
 
 
 
 
 
INTENDED USE

 

 
Your BILLY GOAT ® 

BC Self-Propelled Brush Cutter 

is designed for cutting overgrown weeds, brush and other 

growth down to 3½” (8.9 cm) in height. It is 

not a lawn mower

 

and does not provide the quality cut of a finish 

cut mower. It is designed for use in rural areas and should not be operated in tight or confined areas. 

 

Содержание BC2402 Series





































Отзывы: