Part No. 360251 Form No. F031005B
Page 4 of 12
These labels should be included on your Aerator. If any of these labels are damaged, replace them before putting this equip-
ment into operation. Item and part numbers are given to help in ordering replacement labels.
Label Hot Engine
Part No.400268
EXPLOSIVE FUEL
STOP ENGINE AND ALLOW T O
COOL BEFORE REFUELING.
400268
WARNING
14
15
INSTRUCTION LABELS
ENGINE LABELS
Label LIFT HERE
Part No.360187
13
CONTROLS
Label Instructions AE - Part No. 360262
WARNING
900327
Label Danger Guard
Part No.900327
Honda
FUEL VALVE
(shown in the
CLOSED
position)
CHOKE LEVER
(shown in
RUN
position)
LIFT HERE
WARNING
LIFT HERE WITH CAUTION
THE UNIT WEIGHS OVER 300 LBS.
Label Warning Unit Weight
Part No.360188
ENGINE SPEED CONTROL
Throttle Lever
READ OWNER’S MANUAL
BEFORE OPERATING
USE PERSONAL
PROTECTION EQUIPMENT
TO START, MOVE ENGINE STOP SWITCH TO "ON" AND PULL ROPE.
NOTE:
IT MAY BE NECESSARY TO USE THE ENGINE CHOKE IF
ENGINE IS COLD.
PUSH DOWN ON TINE LIFT HANDLE TO ENGAGE TINES
IN GROUND.
OPERATING INSTRUCTIONS
BEFORE STARTING, MAKE SURE:
FOR PREVENTIVE MAINTENANCE:
INSPECT MACHINE BEFORE EACH USE AND REPLACE ANY WORN AND
DAMAGED PARTS.
EMPTY THE WATER TANK BEFORE TRANSPORTING.
PROPERLY SECURE EQUIPMENT BEFORE TRANSPORTING.
DISCONNECT SPARK PLUG WIRE BEFORE SERVICING UNIT.
USE ONLY A QUALIFIED MECHANIC TO SERVICE THIS MACHINE.
TINE LIFT HANDLE IS IN UP POSITION.
ALL GUARDS ARE ATTACHED.
FILL TANK WITH WATER TO DESIRED LEVEL.
NOTE:
MORE WATER IS REQUIRED IN DRY SOIL.
CHECK ENGINE OIL DAILY.
INSPECT AND CLEAN ENGINE AIR FILTER DAILY.
REPLACE AS NEEDED.
GREASE ALL BEARINGS AND CHECK GEAR REDUCTION OIL LEVEL
ON EVERY ENGINE OIL CHANGE.
ALWAYS:
FULL: 50 LBS.
1/4 FULL: 15 LBS.
1/2 FULL: 27 LBS.
3/4 FULL: 39 LBS.
A E R ATO R
PUSH FORWARD ON OPERATOR’S BAIL TO ENGAGE DRIVE AND
START AERATING.
PUSHING DOWN ON OPERATOR’S HANDLE DURING OPERATION
WILL MAXIMIZE CORING DEPTH.
NOTE:
IT IS NOT NECESSARY FOR THE FRONT WHEELS TO BE IN
CONTACT WITH THE GROUND.
S O I L S H O U L D B E DA M P
W H E N A E R AT I N G .
S O I L S H O U L D B E DA M P
W H E N A E R AT I N G .
F I L L T H I S TA N K
W I T H W AT E R O N LY
RELEASE BAIL TO STOP UNIT.
NOTE:
ENGINE WILL CONTINUE TO RUN WITH BAIL DISENGAGED.
TO TURN UNIT, PULL UP ON TINE LIFT HANDLE TO LIFT TINES
OUT OF GROUND. GRADUAL TURNS CAN BE MADE WITHOUT
LIFTING THE TINES.
WITH TINES UP, PUSH FORWARD ON OPERATOR’S BAIL TO
ENGAGE WHEELDRIVE FOR ASSISTED TURNING.
TO STOP ENGINE MOVE ENGINE STOP SWITCH TO "OFF".
LIFT
HANDLE
OPERATOR’S
BAIL
OPERATOR’S
HANDLE
Label Patent
Part No.360286
Honda
Briggs
Set lever to choke position when
starting a cold engine
Set lever to desired engine speed.
Move lever completely to the left to stop
engine
RUN
CHOKE
STOP
OIL ALERT
ENGINE STOPS IMMEDIATELY.
WHEN OIL LEVEL LOW,
Briggs
ON
OFF
RUN
CHOKE
Read and follow Operating
Instructions before running engine.
Gasoline is flammable. Allow engine
to cool at least 2 minutes before fueling.
Engines emit carbon monoxide,
DO NOT run in enclosed area.
