manualshive.com logo in svg

Billion BiPAC 8700NEXL R2, Руководство пользователя

Поделиться
Скачать
Billion BiPAC 8700NEXL R2 Скачать руководство пользователя страница 218

214

 

 

Federal Communication Commission Interference Statement 

This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses, and can 
radiate radio frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be determined by turning the equipment off 
and on, the user is encouraged to try to correct the interference by one or more of the following 
measures: 

  Reorient or relocate the receiving antenna. 

   Increase the separation between the equipment and receiver. 

  Connect the equipment into an outlet on a circuit different from that to which the receiver is 

connected. 

  Consult the dealer or an experienced radio/TV technician for help. 

 

FCC Caution: 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 
conditions: 

(1) This device may not cause harmful interference 

(2) This device must accept any interference received, including interference that may cause 
undesired operation. 

Any changes or modifications not expressly approved by the party responsible for compliance could 
void the user's authority to operate this equipment. . This device and its antenna(s) must not be co-
located or operating in conjunction with any other antenna or transmitter. 

 

Co-location statement 

This device and its antenna(s) must not be co-located or operating in conjunction with any other 
antenna or transmitter. 

 

FCC Radiation Exposure Statement 

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled 
environment. This equipment should be installed and operated with minimum distance 20cm 
between the radiator & your body. 

 

Содержание BiPAC 8700NEXL R2



























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды