background image

BL-PDSR 30-0319 - 03-07-2019

2-1

SECTION 2

OPERATION

2-1. GENERAL.

This section gives detailed operating instructions for
the lift truck. The instructions are divided into the vari-
ous phases of operations, such as operating lift, driv-
ing, and stopping. Routine precautions are included
for safe operation

2-2. OPERATING PRECAUTIONS.

WARNING

:  Improper operation of the lift truck may

result in operator injury, or load and/or lift
truck damage. Observe the following
precautions when operating the lift truck.

The following safety precautions must be adhered to
at all times.

• Do not operate this truck unless you have been

trained and authorized to do so.

• All warnings and instructions must be read and

understood before using the equipment.

• Equipment must not be altered in any way.

• Equipment must be inspected by a qualified person

on a regular basis.

• Do not exceed the rated capacity. Overloading may

result in damage to the hydraulic system and struc-
tural components.

• Be certain that the lifting mechanism is operating

smoothly throughout its entire height, both empty
and loaded.

• Be sure that mast is vertical - do not operate on a

side slope.

• Be sure the truck has a firm and level footing.

• Avoid overhead wires and obstructions.

• Check for obstructions when raising or lowering the

lift carriage.

• Do not handle unstable or loosely stacked loads.

Use special care when handling long, high, or wide
loads to avoid tipping, loss of load, or striking bysta-
nders.

• Center and carry the load as far back as possible

toward the lift carriage back rest. The center-of-
gravity of the load must not exceed the load center
listed on the nameplate. See Figure 2-1 for load cen-
ter limitations.

• Pick up loads on both forks. Do not pick up on only

one fork.

• When traveling, always lower the load as far as pos-

sible.

• When stacking pallets in racks and it is necessary to

move the load in a raised position, use caution.
Operate truck smoothly.

• Observe applicable traffic regulations. Yield right of

way to pedestrians. Slow down and sound horn at
cross aisles and wherever vision is obstructed.

• Operate truck only from designated operation posi-

tion.Never place any part of your body between the
mast uprights. Do not carry passengers.

• Do not allow anyone to stand or pass under load or

lifting mechanism.

• When leaving truck, neutralize travel control. Fully

lower lifting mechanism and set brake. When leaving
truck unattended, turn off key switch, remove key
and disengage the emergency stop switch.

Figure 2-1   Load Center

R3814

Содержание PDSR 30













































































































































































Отзывы: