7
01-2016A
PLEASE READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT!
PLEASE READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT!
PLEASE READ THIS MANUAL
IN ITS ENTIRETY
PRIOR T
O USING THIS PRODUCT!
PLEASE READ THIS MANUAL
IN ITS ENTIRETY
PRIOR T
O USING THIS PRODUCT!
STEP 6: With three (3) or more adults, carefully raise the assembled ladder stand up until the ladder stand rests into the center of
the v-bar (H) and foot platform assembly(L,M,N) are level. Note: DO NOT stand in the direct path or underneath any treestand at
any time. If need be, drive a stake into the ground at the first ladder rung to prevent the ladder stand from sliding toward the tree
while raising and lowering of the ladder stand.
Note: With two (2) adults raising the treestand into place, have one (1) adult pulling on
the two (2) 16’ stabilizing ropes (T) from behind the tree. By doing so, this helps guide the
treestand safely into place.
STEP 7: To level the v-bar (H) and foot platform assembly (L,M,N), move the ladder stand in or out
until the platforms are level. Once level, stand on the bottom ladder rung until it is firmly seated on
the ground.
Note: When raising/lowering your treestand, DO NOT flex/stress the ladder sections by
arching or bending them as too much stress or flex in the ladder sections will cause per
-
manent damage in the ladder sections.
STEP 8: With the treestand level, and the v-bar (H) flush against the tree trunk, adjust the adjust
-
able support bar assemblies (V) length until the “V” end is firmly against the tree trunk. Tighten
the wingbolt securely.
Note: The ladder sections shall be slightly arched away from the tree.
STEP 9: Locate the one (1) 8’ stabilizing rope (U) (refer to Figure 1). Secure the adjustable support
bar assembly (V) “V” end to the tree using the 8’ stabilizing rope (U) as shown in Figure 8.
Note: NEVER adjust the adjustable support bar assembly (V) once your stand is in position and your platforms are level.
FIGURE 8
ADJUSTABLE SUPPORT
BAR ASSEMBLY SECURED
TO TREE
STEP 1: Select a straight, healthy tree with a minimum diameter of 12-inches (31cm) at the v-bar (H) installation height.
STEP 2: Insure all ladder sections are assembled properly and quick pins (Q) are installed and closed as shown in Figure 1&5 for
each ladder section. Check ALL bolts and locknuts on the entire stand to insure all are securely tightened. Review ALL product
instructions/warnings for proper assembly and final inspection of all the parts to insure all items are free from damage or wear.
Do not use if there are any damaged or missing parts.
STEP 3: Lay the assembled ladder stand face down on the ground with the feet of the lower ladder section 3 or 4 feet (91cm
and 122cm) away from the base of the tree. Locate the adjustable support bar assembly (V) (refer to Figure 1). Install the
adjustable support bar assembly (V) to the fifth ladder rung from the ground level (as shown in Figure 5). Bolt the bar to the
welded tabs using one (1) 8mm x 1-5/8” bolt and one (1) wingnut (as shown in Figure 5
1
). Tighten securely. Make certain
the v-bar portion of the adjustable support bar assembly (V) is extended away from the ladder sections. Note: The adjustable
support bar assembly (V) adjusts for length by loosening the wingbolt (as shown in Figure 5
2
) and sliding the assembly in or
out to accommodate length requirements. Once adjustments have been made, you must retighten the wingbolt prior to use.
STEP 4: Locate the looped ratchet strap (S) (refer to Figure 1). Install the looped end(s) of the ratchet strap assembly to each
side of the v-bar as shown in Figure 6. For installation and threading instructions refer to Figure 7.
STEP 5: Locate two (2) 16’ stabilizing ropes (T) (refer to Figure 1). Install the two (2) 16’ stabilizing ropes (T) on the v-bar, tying
one (1) 16’ stabilizer rope onto each of the two (2) sides of the v-bar as shown in Figure 6. Note: Attach by tying a secure knot.
Allow the looped ratchet strap (S) and the two (2) 16’ stabilizing ropes (T) to hang freely downward.
Wrap sewn loop end
around v-bar.
Pull ratchet through
sewn loop.
Pull assembly tight
around v-bar.
Thread strap through
barrel as shown.
Pull strap tight, then ratchet lever to secure.
Ratchet at least three (3) wraps around barrel.
To release ratchet, push spring-loaded
retaining lock while pulling strap.
1
2
3
4
5
6
FIGURE 7: RATCHET STRAP INSTALLATION AND THREADING (INSTALLATION SITE MAY VARY)
WARNING! As you approach the top of the ladder, attach your full-body fall arrest harness tether to the tree trunk as soon
as possible. After your tether has been attached to the tree, attach the looped ratchet strap to secure the top of the stand
to the tree. Do not sit or stand on the standing platform until the looped ratchet strap has been securely fastened. Failure
to follow these instructions will result in serious injury or death!
WARNING! DO NOT use this, or any other Big Dog product(s) to climb utility poles, telephone poles, structural columns or
any other man-made structures. Never use this or any other Big Dog product(s) around power generation (e.g., transform-
ers, generators, substations, etc.) and/or power transmission equipment. Failure to follow these instructions will result in
serious injury or death!
