BIEMMEDUE GA/N 250C Скачать руководство пользователя страница 6

O

OB

BSSEER

RV

VEED

D  FFA

AU

ULLT

TSS,,  C

CA

AU

USSEESS  A

AN

ND

D  R

REEM

MEED

DIIEESS

FAULTS

CAUSES

REMEDIES

• Check power specifications

• Check power connections

• Check fuse integrity

• Main switch in wrong position

• Select correct position

• Check thermostat position

• Check thermostat operation

• Safety device (control unit, safety thermostat, etc.)

 not reset after a repair

• Press button (9) on the control panel

• The duct gives too much back pressure and

airpressure switch PA1 blocks the heater

• Reduce back pressure by straightening the duct

 or by reducing duct length

• Make sure the gas supply hose has been bled

• Check gas supply pressure

• Make sure the suction and feed grilles are

 not blocked

• Make sure the fan is turning properly

• Check the electric motor and capacitor and,

 if these are faulty, replace

• The flame sensor is not operating correctly

• Remove the flame sensor and clean

• Makes sure the suction and feed grilles

are not blocked

• Make sure the environment is well ventilated

• Make sure the warm air can exit freely

• Make sure the flow and pressure of the gas

 are not too high

• Control unit trips due to irregular operation

 of burner

• Contact After-Sales Service

• Faulty gas pressure switch

• Check the pressure switch and, if necessary,

replace

• Faulty pressure-switch PA

• Check the pressure-switch and, if necessary, 

 replace

• Faulty electronic control unit

• Check the unit and, if necessary, replace

• Faulty thermostat

• Check the thermostat and, if necessary, replace

• Foreign bodies on fan blades

• Remove foreign bodies

• Little air circulation

• Eliminate and obstacles to proper air flow

• Fan noise or vibrations

• Gas pressure switch trips due to interruption of

gas flow (gas pressure switch electric contact

 does not close during operation)

• The safety thermostat trips due to overheating of 

 the combustion chamber (the thermostat electrical 

contact does not close during operation)

• The generator fails to start

• No power supply

• Faulty operation of room thermostat

• Pressure switch PA intervention for fan malfuction

• The generator stops and the indicator light (9)

 comes on

6

Содержание GA/N 250C









Отзывы: