Biasi RIVA COMBI Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 52

background image

RIVA COMBI MANUAL - REV B

7

IMPORTANT INFORMATION

Please read this page carefully.

•

ALL BOILERS MUST BE INSTALLED IN ACCORDANCE WITH NATIONAL, STATE AND
LOCAL PLUMBING, HEATING AND ELECTRICAL CODES AND ORDINANCES, AS
WELL AS THE REGULATIONS OF THE SERVING ELECTRICAL, WATER AND GAS
UTILITIES.

•

All systems should be designed by competent contractors, and only persons
knowledgeable in the layout and installation of heating systems should attempt the
installation of any boiler. It is the responsibility of the installing contractor to see that
all controls are correctly installed and operating properly when the installation is
completed.

•

This boiler is intended for use, only with propane or natural gas. All flammable liquids
(especially gasoline), chemicals, rags, paper, wood scraps, debris, etc., should be
kept away from the boiler at all times. Keep the boiler area clean and free of all fire
hazards.

•

Please read the literature and warranties supplied by the manufacturers for the
various accessory equipment. This equipment is warranted by the respective
manufacturers, not by Quincy Hydronic Technologies, Inc. Each piece of equipment
must be installed and used according to the recommendations of the manufacturer.

Codes and Regulations:

Installation of the boiler and related equipment must conform to national, state and local
regulating agencies and codes applicable to the installation of the equipment. In the
absence of local requirements, the following codes apply:

The above codes are available from:

A. ANSI/NFPA   -  #70 National Electric Code
B. ANSI/NFPA   -  #211 Chimneys and Vents
C. ANSI/NFPA   -  #Z223.1 National Fuel Gas Code
C. ANSI/NFPA   -  Domestic Gas Conversion Burner
D. CAN/CGA      -  B149 Installation Codes
E. ANSI/ASME   - CSD-1

National Fire Protection Association (NFPA)
Battery March Park
Quincy, Massachusetts, 02269
http://www.nfpa.org

CSA International
8501 E. Pleasant Valley Road
Cleveland, OH 44134-5575
http://www.csa-international.org

«
...
5
6
7
8
9
...
»

Содержание RIVA COMBI





















































Отзывы:

Нет отзывов

Похожие инструкции для RIVA COMBI

Бренд: H2O Страницы: 50

Бренд: ideal commercial Страницы: 36

OPTIMAX HE PLUS 25 OV

Бренд: Ferroli Страницы: 40

Rotex A1 BO Series

Бренд: Daikin Страницы: 60

Бренд: IBC Страницы: 78

Бренд: Ariston Страницы: 88

Logano plus SB745

Бренд: Buderus Страницы: 16

Бренд: GAH Страницы: 64

Бренд: ARCA Страницы: 26

Бренд: Thermo Dynamics Страницы: 23

Бренд: Truma Страницы: 28

Бренд: Truma Страницы: 44

Бренд: ACV Страницы: 14

Бренд: ACV Страницы: 20

Бренд: ACV Страницы: 16

Бренд: Ideal Heating Страницы: 31

Knockdown RV-450

Бренд: Bryan Boilers Страницы: 2

Бренд: Bryan Boilers Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды