3
REMOTE CONTROL
External Infrared Receiver (Biamp #909-0030-00): The receiver consists of a black plastic box,
which contains an infrared photo detector, an LED indicator, and three screw terminals. To install the
receiver, first take off the front cover by removing the four screws. Mount the receiver to a wall or
other surface, using the two screw holes on the back cover (screws not included). The receiver
should not be mounted in direct sunlight, or pointed directly at fluorescent lighting. For best results,
there should be an unobstructed line-of-sight from transmitter to receiver. The receiver may be wired
up to 2000 feet from the IWA unit, using 2-conductor shielded cable (not included). Route the cable
through the access hole on the bottom of the receiver. The three screw terminals inside the receiver
("GND", "IR2", & "IR3") directly correspond to the Remote 1 and Remote 2 terminals on the Remote
Control PCB (Remote 1 and Remote 2 share a common "GND" terminal). Remote Infrared
Receivers may be connected to Remote 1 and/or Remote 2, depending upon the particular
application. Connect the cable shield to the "GND" terminal at each end. Use the two conductors to
connect "IR2" to "IR2" and "IR3" to "IR3". Replace the receiver front cover. When the IWA unit is
turned on, power is delivered to the receiver. The LED indicator inside the receiver, and the IR LED
indicator on the Remote Control PCB, will flash whenever infrared information is detected. NOTE:
The Infrared Receiver includes a "Remote Translator", which allows remote control of Advantage
products via third-party controllers (instructions included with receiver).
InfraRed Receiver
External Infrared Receiver
(Biamp #909-0030-00)
Wall-Mount Panel (Biamp #909-0073-00): The wall-mount is a "hard-wired"
control panel, which receives power from the Remote Control PCB. There are
no batteries to wear out, and it is not easily lost or stolen. The wall-mount may
be wired up to 2000 feet from the IWA unit, using 2-conductor shielded cable
(not included). Remove the mounting box from the front panel. Route the
cable through a "knock-out" hole on the rear of the mounting box. Install the
mounting box in a wall or panel. The three screw terminals on the Wall-Mount
Panel circuit board ("GND", "IR2", & "IR3") directly correspond to the Remote 1
and Remote 2 terminals on the Remote Control PCB (Remote 1 and Remote 2
share a common "GND" terminal). Wall-Mount Panels may be connected to
Remote 1 and/or Remote 2, depending upon the particular application.
Connect the cable shield to the "GND" terminal at each end. Use the two
conductors to connect "IR2" to "IR2" and "IR3" to "IR3". Install the front panel
in the mounting box. The wall-mount has twenty-eight buttons. The Select
1~8 buttons choose a desired preset from non-volatile memory. The Setup
1~8 buttons create presets by storing current settings (levels & relays) in non-
volatile memory. Once presets have been established, the Setup 1~8 buttons
may be disabled. The MUTE, VOL
▲
, and VOL
▼
buttons (Main & Zone)
provide volume up, volume down, and volume off functions for the mixer
outputs. The ON and OFF buttons (A, B, & C) provide switching of the
respective relays (on Remote Control PCB). When the IWA unit is turned on,
power is delivered to the Wall-Mount Panel and the green LED indicator will
light. The red LED indicator on the Wall-Mount, and the IR LED indicator on
the Remote Control PCB, will flash whenever infrared information is detected.
The Wall-Mount Panel includes an infrared detector (below LED indicators),
which allows it to operate as an External Infrared Receiver as well. The
infrared detector may be disabled via a circuit board jumper strap. Complete
instructions are included with the Wall-Mount Panel.
Wall-Mount Panel
(Biamp #909-0073-00)
MAIN
ZONE
A
B
C
SETUP
SELECT
5
1
2
3
4
6
7
8
OFF
OFF
OFF
ON
ON
ON
MUTE
VOL
VOL
MUTE
VOL
VOL
5
1
2
3
4
6
7
8
ADVANTAGE IWA
Remote Interface Kit (Biamp #909-0041-00): The Remote Interface Kit allows the user to create a customized control panel, using his
own switches, enclosure, and panel. It can provide up to 40 buttons (12 more than standard remote controls). The Remote Interface Kit is
a tested circuit board assembly, which includes two wiring harnesses. The circuit board connects to the Remote Control PCB in exactly the
same way the External Infrared Receiver does, using 2-conductor shielded cable (not included), and may be wired up to 2000 feet from the
IWA unit. The three screw terminals on the Remote Interface Kit circuit board ("GND", "IR2", & "IR3") directly correspond to the Remote 1
and Remote 2 terminals on the Remote Control PCB (Remote 1 and Remote 2 share a common "GND" terminal). Remote Interface Kits
may be connected to Remote 1 and/or Remote 2, depending upon the particular application. When the IWA unit is turned on, power is
delivered to the circuit board. The circuit board is 2.27"W by 2.65"H, with four mounting holes (2" centers) and #6 mounting hardware
provided. Complete instructions are included with the Remote Interface Kit.
585.0052.00
