15
5. FITTING THE HANDLEBAR.-
Bring the handlebar (57) up to the
handlebar stem (55).
Refit the screws (105) and washers
(6) (63), Fig.6, and tighten securely,
then fit the bracket cover (59) and
screw with screw (61).
6. BOTTLE HOLDER ASSEMBLY.-
Place the bottle holder (60) in the tube
(55), and screw with screws (61)
Fig.6.
7. FITTING THE MONITOR.-
Next, connect terminals, sticking out of
the
handlebar
post
(55),
and
terminals, sticking out of the monitor
(58), Fig.6.
Place the monitor (58) on top of the
plate on the main post (55), as shown
in Fig.6, making sure not to pinch the
wires.
Use supplied screws to hold the
monitor in place, Fig.6.
8. FITTING THE SADDLE PROFILE
Firstly (Fig 7), place the saddle profile
(77) close to the main body (1) and
connect terminal from saddle profile.
Afterwards introduce tube of main
body in aluminium profile, paying
special attention to the cables.
Insert the head of the screws in the
slots of the rail and tighten the nuts.
Fit the trim (74). Finally, place screw
(75) and tighten securely.
9.
ATTACHING THE SADDLE
Take the saddle back support tube
(91) and insert the cover (93). Slip the
saddle back support tube (91) over the
boss on the body (77), Fig.8.
Refit the screws (62), and the washers
(5) (63), Fig.5, and tighten securely.
Lower the bottom trim section (93)
down over the boss section of the
body (77).
Place saddle back as shown in Fig 8
and screw with screws (94) securely.
To adjust the seat position, release
the
knob
(89)
by
turning
counterclockwise. Position it and
tighten the knob before starting the
exercise.
10.
LEVELLING.
Once the unit has been placed into its
final position, make sure that it sits flat
on the floor and that it is level. This
can be achieved by screwing the
adjustable feet (70) up or down, as
shown in (Fig 9).
To level the seat:
Loosen the screws (84) under the rail.
Level seating position with the screws
(108). Tighten the screws (84) again.
FIG. 11.
11.
MOVEMENT & STORAGE
The unit is equipped with wheels (67)
to make it easier to move. The wheels
located at the front of your unit make it
easier to move it into a chosen
position, by lifting the rear of the unit
up slightly and pushing it, as shown in
(Fig 9). Store your unit in a dry place,
preferably not subject to changes in
temperature.
12.
MAINS CONNECTION
Insert the jack (g) on the transformer
(97) into the connection hole (h) on
the main body (1) (bottom, rear of the
machine)
and
then
plug
the
transformer into a 230 V mains supply,
(Fig 12).
Do not hesitate to get touch with the
Technical Assistance Service if you
have any queries by phoning customer
services (see last page in manual)
BH RESERVES THE RIGHT TO
MODIFY THE SPECIFICATIONS OF
ITS PRODUCTS WITHOUT PRIOR
NOTICE
Содержание i.TFR ERGO H650i
