SW-Stahl und Werkzeugvertriebs GmbH
Tel. +49 (0) 2191 / 46438-0
F
5
6
e
s
s
a
r
t
S
r
e
s
u
k
r
e
v
e
L
ax +49 (0) 2191 / 46438-40
e
d
.l
h
a
t
s
w
s
@
o
f
n
i
:l
i
a
M
-
E
d
i
e
h
c
s
m
e
R
7
9
8
2
4
-
D
Instruction Manual
BGS technic KG
Bandwirkerstr. 3
42929 Wermelskirchen
Tel.: 02196 720480
Fax.: 02196 7204820
www.bgstechnic.com
© BGS technic KG, Copying and further use not allowed
OPERATE
1. Place the sand blast cabinet near a 230V/60Hz AC electrical outlet. Make sure the receptacle will
accept the 3 -prong plug so that the unit will be properly grounded. Also make sure to check the
power source is adequate for use with this blast system.
2. Attach the air supply line from a compressor capable of maintaining 5 CFM at 80 PSI to the inlet
connector found on the right side of the cabinet. Because of variation in air supply systems, the air
inlet coupling is not provided. Use the particular fitting that is compatible with your air supply
system. Do not operate the blasting system at over 100 psi.
3. Check the air supply line fittings and hose attachments to the rear of the gun. Also make sure the
media supply hose is attached lightly on the nipple on the underside of the gun.
4. Place no more than 10 pounds of abrasive media into the center of the cabinet. Excessive
amounts will create clouded cabinet conditions, blow by media through the exhaust or sluggish
and ineffective blasting performance.
5. With the air supply connected, all fittings and joints not leaking and the unit is plugged in. You are
ready to test the blasting system. Now follow these steps for start up operation.
6. Place the part in the cabinet. Always close and latch the lid after placing the part in the cabinet
prior to blasting. Severe injury to the skin and eyes may result from exposure to the blast stream.
After pulling your hands into the gloves grasp the gun and depress the trigger. This should begin
the blasting flow. If no flow is seen you may need to clear the tube by covering the gun nozzle
momentarily.
7. Now you may begin finishing the part. You should move the blast stream continuously over the
part in an even and circular motion. The flow should not be too hard or concentrated to avoid
undesirable peening.
PARTS
1
Transparent Top Lid
7B
RF LR Leg
19
1/4” Hose Clamp
1-1
Top Lid Position Chain
8
Screw 1/4x3/8"
20
Glove Clamp
1-2
Screw
9
Screw 5/32x3/8"
21
Glove
1-3
Nut
9-1
Nut 5/32"
22
Self Drilling Screw
1-4
Movable Leaf
10
Nut
23
Screw
1-5
Plastic Screw
11
Sanding Gun
24
Air cleaner
2
Front Panel
12
Nozzle
24-1
Filter
3
Rear Panel
13
Air Supply Hose
25
Anchor Plate
4R
Right Panel
14
Plastic Suction Hose
26
Lamp
4L
Left Panel
15
Steel Suction Hose
26-1
Feed thru
5
Base
16
Air Hose Connector
27
Wire Connector Box
6
Lamp Clamp
17
Washer
27-1
AC-AC Adaptor
7A
LF RR Leg
18
Air Supply Connector