BFT GIOTTO 30-50 BT, Инструкция по установке и эксплуатации, Страница: 17 / 21

INSTALLATION MANUAL
TABLE B: LOGIC MENU (
logic
)
Logic Default Definition
Cross
out
setting
used
Description
TCA
ON
Automatic
Closing Time
ON Switches automatic closing on.
OFF Switches automatic closing off.
Ibl open
ON Block Pulses
ON The start pulse has no effect during opening.
OFF The start pulse has effect during opening or closing.
ibl TCA
OFF Impulse lock TCA
ON The Start impulse has no effect during the TCA dwell period.
OFF The Start impulse becomes effective during the TCA dwell period.
2 step
OFF 2 step
ON
Enables the 2-step logic (prevails over
the “3-step logic”).
Response to the START impulse
Barrier 2 steps 3 steps 4 steps
closed
opens opens
opens
on closing stop
open
closes
closes closes
on opening stop + TCA stop + TCA
after stop opens opens opens
OFF
Disables the 2-step logic, activating the
4-step logic if the “3-step logic” is OFF.
3 step
ON 3 step
ON
Enables the 3-step logic (if the “2-step
logic” is OFF).
OFF
Disables the 3-s6tep logic, activating the
4-step logic if the “2-step logic” is OFF.
preal
OFF Pre-alarm
ON The flashing light comes on approx. 3 seconds before the motors start.
OFF The flashing light comes on at the same time as the motors start.
hold to
Run
OFF Deadman
ON
Hold-to-run operation: the manoeuvre continues as long as the OPEN and CLOSE
control keys are kept pressed. The radio transmitter cannot be used.
OFF Normal impulse operation.
Photoc.open
ON
Photocells
during opening
ON
When beam is broken, operation of the photocell is switched off during opening. During closing,
movement is reversed immediately.
OFF
When beam is broken, photocells are active during both opening and closing. When beam is
broken during closing, movement is reversed only once the photocell is cleared.
fast cls
OFF Rapid closing
ON
Closes barrier after photocell disengagement, before waiting for the end of the TCA (automatic
closing time) set.
OFF Command not entered.
test phot
OFF Photocell test
ON Switches photocell testing on
OFF
Switches photocell testing off
If disabled (OFF), it inhibits the photocell testing function, enabling connection of devices not
equipped with supplementary test contacts.
ster
OFF Master/slave
ON Control panel is set up as the Master unit in a centralized serial connection system.
OFF Control panel is set up as a Slave unit in a centralized serial connection system.
fixed code
OFF Fixed code
ON Receiver is configured for operation in fixed-code mode.
OFF Receiver is configured for operation in rolling-code mode.
radio prog
ON
Remote control
programming
ON
Enables wireless memorizing of transmitters:
1- Press in sequence the hidden key (P1) and normal key (T1-T2-T3-T4) of a transmitter that has
already been memorized in standard mode via the radio menu.
2- Press within 10 secs. the hidden key (P1) and normal key (T1-T2-T3-T4) of a transmitter to be
memorized.
The receiver exits programming mode after 10 secs.: you can use this time to enter other new
transmitters. This mode does not require access to the control panel.
IMPORTANT: Enables the automatic addition of new transmitters, clones and replays.
OFF
Disables wireless memorizing of transmitters.
Transmitters are memorized only using the relevant Radio menu.
IMPORTANT: Disables the automatic addition of new transmitters, clones and replays.
alar sca
ON SCA Alarm
ON
The SCA contact (terminals 21-22) behaves as follows:
- with barrier open and on opening: contact closed (warning light on)
- with barrier closed:contact open: (warning light off)
- on closing: intermittent contact (blinking)
OFF The SCA contact closes according to the modes set by the Alarm Time parameter.
change ot.
OFF Reversing motion
ON Change this parameter if the opening direction needs to be changed
OFF Standard operating mode.
open-ti er
(special dip 2*)
OFF TIMER su OPEN
ON Input between terminals 15-27 works as TIMER.
OFF Input between terminals 15-27 works as OPEN.
*=Refer for universal handheld programmer.
28
- GIOTTO 30-50 S BT / GIOTTO 30-50 BT
D811768 00100_03