background image

 

Form Title: 

Document #: 

INSTALLATION AND MAINTENANCE MANUAL 

MM-CH004 

(Form: DEF-006A-1) 

Revision: 

0

 

Document Title: 

Date: 

EXTERNAL CHEMICAL HYDRAULIC VALVE

 

Oct. 20, 2020 

Page:

 

7 of 10

 

 

 

Betts Industries Inc.   

   814·723·1250   

   1800 Pennsylvania Ave. West   

   Warren, PA 16365   

   

www.BettsInd.com

 

 

Print Date: 1/22/2021   

This form is considered uncontrolled 24 hrs. after print date.

 

 
 

 

Hold cap collar stationary while using spanner wrench 
(16236MS) to unscrew seal retainer ring (18). 

  If lower stem (14) unscrews from the upper stem (6) it will be 

necessary to clamp lower stem (14) in a vice to unscrew seal 
retainer ring (18).  Care should be taken not to damage the 
lower stem (14) by applying too much pressure with the vice. 

  If lower stem (14) remains in valve body after the seal retainer 

ring (18) was removed, continue to hold the cap collar (2) and 
insert a ¼” thick x 2” wide piece of plate into the slots on the 
lower stem (14) and unscrew lower stem (14). 

 

  Remove bearing (17) from seal retainer ring (18) and replace 

with new from kit. 

  If bearing is not present, inspect seal retainer (18) for counter bore to receive 

bearing.  If the counter bore is not present, replace seal retainer (18) with the up 
to date version, including the bearing (17).  See Engineering Bulletin 8-08 for 
more detail on the bearing (17).   

  Using care not to damage the seal surface of the seal retainer ring (18), remove 

old main seal (16) and install new main seal (16) into lower stem (14). 

CORRECT 

INCORRECT 

Содержание CH46949LHT











Отзывы: