IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!!
TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND RECEIPT
Step 1:
Identify all parts packed in the carton against the parts list. Remove all protective materials. Place parts on a non-abrasive surface to avoid scratching. If you are missing any parts or are unsure as how to
proceed with the assembly, call our Customer Service Center at 1-800-416-3511.
Do not attempt assembly if any parts are missing or damaged.
Step 2:
Place the swivel base (with rocker assembly) on a flat, solid surface. Make sure the rocker assembly is positioned all the way into the base. It may have shifted or vibrated out during shipment.
Step 3:
Important: We recommend 2 people work together to assemble the chair.
Note the arrow labels on the "U" bar and the rocker assembly. Also note the horseshoe shape of the rocker plate. Point the
open end of the horseshoe away from you. The arrows on the rocker assembly should be pointing towards you. Set the chair frame on the rocker assembly with front of the seat facing you and the arrows
on the "U" bar pointing towards you as shown in
Figure 1
. This is very important for a safe, balanced rocking motion.
If the chair frame has
been properly positioned
on the rocker assembly, all arrows
on the "U" bar and rocker
assembly will be pointing
in the same direction.
Step 4:
Critical Step:
The "U" metal plates must be installed in the proper location.
Read this step and carefully examine. Insert the "U" metal plate, so that the "U" bar and rocker plate are between both
sides of the "U" metal plate. Make sure that the holes in the "U" metal plate are completely aligned with the holes in the "U" bar as shown in
Figure 1
. Guide the bolts through the holes on the top side
of the "U" metal plate, through the holes in the "U" bar portion of the chair, through the holes in the rocker plate and then, most importantly, through the holes in the bottom side of the "U" metal plate. It
is very important that the holes in the bottom portion of the "U" metal plate be placed directly beneath the holes in the rocker plate. Add a washer and a nut to each bolt as shown in
Figure 2
.
Hand
tighten nuts 3-4 revolutions only.
Repeat the same procedure on the other side.
CAUTION:
Failure to place "U" metal plates under the rocker plates and above the
"U" bar exactly as shown in diagram will cause the bolt heads and nuts to damage the
structure of the rocker
plates and the "U" bar. Damage due to over tightening of bolts
or improper assembly could cause injury and may void
your warranty.
Step 5:
Tighten all nuts and bolts with the hex wrenches provided.
Do not over tighten.
Remove arrow labels from "U" bar and rocker assembly. Cover bolts with
bolt covers.
Step 6:
Your chair should be ready for use. If your chair is not rocking properly, double-check your assembly procedure, especially Step 3. If the chair rocks too far forward to or is difficult to rock backwards, you
have probably installed the seat frame backwards on the rocker assembly. If you need further assistance, please call our Customer Service Center at 1-800-416-3511.
Estimated assembly time
：
20 minutes.
IMPORTANT NOTE: Damage to welds or frames resulting from over tightened bolts or improper assembly is not covered under our warranty. Please read all instructions carefully before assembly. If
you have any questions regarding your assembly, call our Customer Service Center at 1-800-416-3511.
NOTE: MAKE SURE ARROWS
FROM BOTH THE "U" BAR
AND ROCKER ASSEMBLY
ARE POINTING IN THE
SAME DIRECTION!
SEAT DESIGNS MAY
VARY BUT THE ASSEMBLY
IS THE SAME
Figure 1
ROCKER PLATE
E
D
D
A
"U" BAR
ROCKER
ASSEMBLY
"U" BAR
H
COVER
FOOT CAP
Figure 2
B
C
I
Page 2
