background image

8

5. BATTERY MAINTENANCE

For maintenance and recharging, follow the instructions provided by the battery 
manufacturer.

6. BATTERY DISPOSAL

When the battery reaches the end of its life, it must be disconnected by certi-
fi ed professional, then lifted (using the handles and suitable lifting device) to 
remove it from the battery compartment.

7. CONNECTING THE BATTERY CHARGER

Beneath the recovery tank there is the battery connector (

7

), the battery charger 

connector must be plugged into. Disconnect the battery plug and plug the 
charger into the machine plug.

WARNING: This process must be carried out by qualifi ed person-
nel. The incorrect or imperfect connection of the cables to the 
connector can seriously harm people and damage objects.

8. RECHARGING THE BATTERIES

Perform one complete battery charge cycle before using the machine.
Avoid totally discharging the batteries!  This can cause permanent damage. 
Recharge as soon as the battery discharged signal light starts to fl ash.

WARNING: Never leave the batteries completely discharged, not 
even if the machine is not being used. This can cause perma-
nent damage to them. While recharging, keep the recovery tank 
raised.

Danger of inhalation of gas and leakage of corrosive liquids.

Danger of fi re.

MACHINE PREPARATION

Содержание Stealth ASD26BT

























































Отзывы: