USE
Start / Stop
To start the angle grinder, push the safety lever forward, while pressing the start lever
(picture 6-m,n)
. Keep the start lever pressed
during the job to be performed. Releasing the lever will cause the angle grinder to stop within 5s.
The grinder is fitted with a rear air outlet
(picture 7-l)
.
When the grinding wheel stops, place the grinder in a firm and safe position. The grinding wheel does not stop immediately.
Grinding wheel installation/replacement
Install the grinding wheel on the angle grinder
(pictures 3, 4)
as follows:
–
Lock the “spindle lock” trigger by hand
(picture 4-g)
. Loosen the disc locking flange of the rotating grinding wheel spindle, fitting the
round pin wrench into the flange, and keeping the “spindle lock” trigger pressed. Then pull the flange out completely;
–
Fit in the grinder wheel, placing it between the two flanges (disc flange and disc locking flange). Check the direction of rotation of
the grinding wheel. The angle grinder can rotate in one direction only
, namely clockwise
(picture 5)
;
–
Screw the disc locking flange by hand; then tighten the flange using the round pin wrench and keeping the rotating spindle locked
with the “spindle lock” trigger;
–
Make sure that the grinding wheel has been fixed correctly.
Replace the angle grinder wheel as follows:
–
Unlock the disc locking flange using the round pin wrench and keeping the rotating spindle locked with the “spindle lock” trigger;
–
The grinding wheel has thus been released and can be removed;
–
Fit in the new grinding wheel and follow the above instructions.
Always disconnect the air supply before making adjustments or fitting in the grinding wheel. This precaution will prevent the pneumatic
tool from being accidentally started.
While using the angle grinder, IT IS FORBIDDEN to press the “spindle lock” trigger, because the flange and the grinding wheel will get
loose, thus becoming unlocked.
Lubrication/Greasing
The pneumatic tool must be connected to a filter-lubricator unit (we recommend Beta item 1919F1/4) provided with an air-oil microfog
mixer, set at two drops per minute. This will result in a high-performing tool and wear-resistant mechanical parts.
If lubrication is not provided to the line, oil ISO 32 must be periodically poured into the pneumatic tool, through the air supply hole
(picture 7-p)
.
Furthermore, the angle grinder must be periodically greased, through the grease nozzle, using grease EP2
(picture 5-i)
.
MAINTENANCE
Maintenance and repair jobs must be carried out by trained personnel only. For such jobs, you can contact Beta Utensili S.P.A.’s repair
centre through your Beta dealer.
DISPOSAL
The pneumatic tool, accessories and packaging should be sent to a waste disposal centre, in accordance with the laws in force in your
country.
WARRANTY
This tool is manufactured and tested in accordance with current EU regulations, and is covered by a 12-month warranty for professional
use or a 24-month warranty for nonprofessional use.
We will repair any breakdowns caused by material or manufacturing defects by fixing the defective pieces or replacing them at our
discretion.
Should assistance be required once or several times during the warranty period, the expiry date of this warranty will remain unchanged.
This warranty will not cover defects due to wear, misuse or breakdowns caused by blows and/or falls. In addition, this warranty will no
longer be valid if any changes are made, or if the pneumatic tool is forced or sent to the customer service in pieces.
This warranty explicitly excludes any damage to people and/or things, whether direct or consequential.
DECLARATION OF CONFORMITY
We hereby declare, assuming full responsibility, that the described product complies with all the relevant provisions of Machine
Directive 2006/42/EC and amendments thereto, as well as with the following standard:
• EN ISO 11148-7
The Technical Brochure is available at:
BETA UTENSILI S.P.A.
Via A. Volta 18 - 20845 Sovico (MB) - ITALY
Name and title of person in charge
MASSIMO CICERI
(Managing Director)
BETA UTENSILI S.P.A.
Date 01/06/2015
Via A. Volta 18
20845 Sovico (MB)
ITALY
