Best Barns Cypress R Скачать руководство пользователя | Manualshive

Страница: 9 / 19

background image

1.

Cut (2) two 72" 2x4s to a length of 69-1/2".

2.

Cut (4) four 68-1/2" long 2x4 to a length of 60-1/4".

3.

Mark spacing as shown on left and assemble a wall

frame using (4) four 72" long 2x4s, (1) one 69-1/2
header support and (2) two 60-1/4” top and botom
plates. Repeat to assemble another wall frame.

60-1/4" Top Plate

19-3/4"

24"

69-1/2" Header

Support

2.

Install a 48" x 76" siding panel to the back wall. Use 8d galv. nails.

Nail along the adjoining siding panel.

Step 5

Set Walls

1.

Secure the back wall between the end wall panels. Secure panels together at the corners.

Use (4) four 10d sinkers per corner. Nail wall panels to the floor. Nail through the bottom

plate. Space 10d sinkers 24" apart.

Step 4

Assemble Front Wall Frames

Nail Along Siding Edge

«
...
7
8
9
10
11
...
»

Содержание Cypress R




















Отзывы:

Нет отзывов

Похожие инструкции для Cypress R

Бренд: Palmako Страницы: 154

GNISTRA PAV-5841-1I

Бренд: landskap Страницы: 34

Бренд: Lasita Maja Страницы: 23

Бренд: Solid Страницы: 32

SLATTED DINING PERGOLA

Бренд: Forest Страницы: 5

Бренд: Palmako Страницы: 96

Бренд: Storite Страницы: 8

Бренд: Karibu Страницы: 28

JUTLAND 18 2320 IL2320 R1 F0

Бренд: Gartenpro Страницы: 34

Бренд: Feider Machines Страницы: 20

GS84-SLIDER-METAL-FJ

Бренд: OLT Страницы: 38

Бренд: Palmako Страницы: 77

Бренд: Palmako Страницы: 25

Бренд: Palmako Страницы: 114

Бренд: Finn Art Blockhaus Страницы: 22

Бренд: Palmako Страницы: 54

Бренд: Tuindeco Страницы: 18

Grand Gardener 44

Бренд: Rion Страницы: 81

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды