Bernal Sensor-Line S 401, Инструкция по эксплуатации

Страница: 14 / 24

S 401 GB
- 14 -
03-06
connections
e
hown in Fig. 25. For the activation and set-up
to be
nted.
The standard circuit board B 300.01 has the
follo
tion
Sta
term
The board, the start
button external and the radio receiver have the
ame function during operation (exception:
drive
oor
art button activates
the
g
mergency stop during door open move-
s to be applied. The connection ca-
le has to be laid fail safe. (e.g. with cable
type: ÖLFLEX-CLASSIC-100 2x,5mm²).
Light barrier with integra heck accord-
ing to safet
tr
te
te
re
te
terminal 7 (S): signal
rminal 8 (-): earth
sub point 4 has to be set on 1 (= active).
he receiver is always connected to the mains
ltage.
he transmitter is only active when the drive is
orking. When the drive is activated, the
ansmitter of the light barrier receives his volt-
ge.
he receiver is being activated via the
ansmitter diode and the signal of the light
arrier is switched on.
efore every start the function of the light bar-
er is being controlled.
there occurs an error on the light barrier,
ere is no start possible!
If the light barrier is activated during door clos-
ing, the drive stops and reverses (completely
or partially, according to the setting on the cir-
cuit board, menu point b1).
If there is an activation while the door opens,
there is no reaction.
CAUTION:
3.6.2 Functions and
The assembly as well as the connection- and
adjustment possibilities of the circuit board ar
s
of some connections (for example, light barrier,
safety edge, etc.) some individual adjustments
s described in paragraph 3.6.3 have a
impleme
wing connection possibilities and func-
s:
rt button external terminal 1 (earth) and
inal 2 (signal)
start button on the circuit
s
learn function). With the start button the
can be started and stopped. During d
movement, pressing the st
the soft-stop.
Emergency stop terminal 3 and terminal 4
Wire jumper bridges terminal 3 and 4, if
emergency stop is not connected. Activatin
the e
ment, the drive is immediately stopped; when
activating while the door closes, the door stops
immediately with reversion.
If you are using a slip door, a fail safe slip door
contact ha
b
ted c
y category 2 EN 954
ansmitter:
rminal 5 (+): 80 mA / 24 V
rminal 6 (-): switched earth
ceiver:
minal 5 (+): 80 mA / 24 V r
te
Light barrier is not connected: terminal 7 and 8
are open, Menu b sub point 4 has to be set on
0 (=inactive).
When using a light barrier: menu
b
T
vo
T
w
tr
a
T
tr
b
B
ri
If
th
During the learn function, the light
barrier is not activated.
Connection safety edge 8,2 or 22 kOhm
When using a safety edge, the menu point b
sub point 5 has to be set on 1 (=active).
If there is no light barrier connected simultane-
ously (menu b sub point 4 =inactive) the safety
edge has to be just connected on terminal 7
and 8.
With an additional connected light barrier, the
safety edge has to be connected in-line with
the receiver signal of the light barrier (terminal
7) (in menu b the light barrier and the safety
edge have to be activated).
Isolated normally open output for door-
closed contact or connection warning lamp
on automatic closing terminal 9 and 10
230VAC / max 1A cos Phi = 1
30VDC/ max.1A
The external wires have to be protected with
max. 1A delay fuses.
a) Red / green light module is not installed:
When setting menu point b3 (automatic closing)
on 0 (=inactive) the clamps 9 and 10 are the
door-closed contact.
When setting b3 on 1 (=active) the terminals 9
and 10 are a isolated normally open output for a
warning lamp for automatic closing.
b) Red / green light module installed (optional)
The clamps 9 and 10 are generally door-closed
contact.
The setting of the pre-warning period automatic
closing is possible on menu point U or H (when
red / green light module is plugged).
The automatic closing period (opening period)
can be set on menu point A.
External lighting terminal 15 and terminal
16, 230 VAC/60W (max.)
t, according to the set adjust-
nu L, the internal and external
ht is on.
Connection earth terminal 17
Earth e.g. for external lighting
Connection antenna to terminal 25 and 26
To avoid interferences with the circuit board we
recommend generally: when using a pluggable
receiver (MOLEX 10-pol), connect the antenna
directly to the receiver. If this is not possible, a
rod antenna can be connected to clamps 25
and 26.
Attention: Operates only in connection with a
receiver plugged in the MOLEX-socket.
After every star
ent time at me m
lig