Berkel X13AE, Руководство пользователя

Страница: 9 / 16

X13 & X13A O
wner
/O
peratOr
M
anual
• 7
X13E & X13AE O
wner
/O
peratOr
M
anual
• 7
Operation
General
1.­ Check­to­see­that­the­center­plate­and­product­table­are­in­place­on­the­slicer­and­the­gauge­plate­is­
completely­closed.­The­holes­in­the­bottom­of­the­center­plate­fit­over­the­bottom­mounting­studs­in­
the­ring­guard­and­the­center­plate­locking­knob­is­at­the­top­of­the­center­plate.­The­product­table­
slides­completely­onto­the­support­arm­and­is­secured­with­the­red­product­table­locking­knob.
2.­ If­the­slicer­is­an­automatic,­then­make­sure­the­automatic­engage­knob­on­the­right­side­of­the­table­
support­arm­is­pushed­in,­towards­the­left.
3.­ Plug­the­slicer­in.­The­pilot­light,­between­the­start­and­stop­buttons­will­illuminate.
4.­ Push­the­green­ON­button­and­the­slicer­blade­will­start­to­turn.­Press­the­red­STOP­button­to­stop­
the­knife.
Automatic Operation
5.­ If­you­have­an­automatic­slicer,­with­the­slicer­stopped,­pull­the­automatic­engage­knob­fully­out­on­
the­right­side­of­the­machine.­This­will­put­the­slicer­in­the­automatic­mode.
6.­ Push­the­speed­selection­button­to­change­the­speed:
­ ­ One­illuminated­LED­indicates­20­slicers­per­minute­(slow­speed)
­ ­ Two­illuminated­LED’s­indicates­40­slices­per­minute­(medium­speed)
­ ­ Three­illuminated­LED’s­indicates­60­slices­per­minute­(high­speed)
7.­ Pushing­the­stroke­length­selection­button­changes­the­length­of­the­stroke.­This­allows­smaller­
products­to­be­sliced­quicker,­without­the­table­moving­any­faster.­Make­sure­the­stroke­length­is­
longer­than­the­width­of­the­product.
­ ­ One­illuminated­LED­indicates­1/3­of­the­total­possible­stroke­length
­ ­ Two­illuminated­LED’s­indicates­2/3­total­possible­stroke­length
­ ­ Three­illuminated­LED’s­indicates­full­stroke­length
8.­ Press­the­green­START­button­and­the­product­table­will­slowly­come­to­its­forward­position­to­find­
its­home­position.­Once­it­gets­back­to­the­home­position,­then­it­will­start­to­go­back­and­forth­at­
the­preset­speed­and­stroke­length.
9.­ Push­the­red­STOP­button­and­the­table­will­complete­its­stroke­and­stop­in­the­home­position.
10.­As­long­as­the­slicer­remains­in­the­automatic­mode­it­will­remember­its­home­position­and­always­
start­right­up­when­the­green­START­button­is­pushed.­It­will­always­start­slow­and­gradually­build­
up­to­its­full­speed.­This­is­the­“soft­start”­feature.
11.­ Each­time­you­take­the­slicer­out­of­the­automatic­mode,­and­then­back­into­the­automatic­mode,­it­
will­always­find­its­home­position­before­it­starts­to­run­(as­indicated­in­step­#8).
12.­Each­time­you­activate­the­slicer­into­automatic­mode,­the­last­speed­and­stroke­length­settings­will­
be­remembered­until­power­is­disrupted­from­the­slicer­(i.e.­disconnecting­the­power­cord­from­
the­outlet).­Once­power­is­reconnected­to­the­slicer,­the­default­for­automatic­is­slow­speed­and­full­
stroke­length.