Berchtold CHROMOPHARE F 300 Скачать руководство пользователя страница 9

Страница: 9 / 67

DANGER

Risk of electrocution!

Touching live electrical components is life threatening. Damage to insula‐
tion or individual components can cause fatal injury.

Therefore:

1. If insulation is damaged, immediately cut off the power supply

and initiate repairs.

2. Electrical work is to be performed by skilled electricians only.
3. For all work on the electrical system, disconnect it from the

mains and check that it is free of voltage.

4. Before performing any maintenance, cleaning or repairs, turn

off the power supply and secure it against accidental switch-
on.

5. Do not bypass or deactivate fuses. Make sure the number of

amperes is correct when changing fuses.

6. Keep conductive parts away from humidity. It can cause a

short circuit.

WARNING

Use of non-EMC flat screens and switched-mode power supplies is life-
threatening.

Radiation disturbances can skew measurement results of medical devi‐
ces (e.g., monitoring of vital functions). This can result in life-threatening
situations.

Therefore:

1. Use only UL- or IEC-rated (UL60601-1, IEC 60601-1) flat screens

and switched-mode power supplies.

Electrical current

EMC risks (flat screens)

Examination light CHROMOPHARE F 300

Safety

Содержание CHROMOPHARE F 300




































































Результаты поиска

Содержание CHROMOPHARE F 300

Отзывы:

Похожие инструкции для CHROMOPHARE F 300

Бренды по названию

Популярные бренды

Berchtold CHROMOPHARE F 300, Руководство по предварительной установке

Результаты поиска

Содержание CHROMOPHARE F 300

Отзывы:

Похожие инструкции для CHROMOPHARE F 300

Бренды по названию

Популярные бренды