BenQ PH460 Скачать руководство пользователя | Manualshive

Страница: 62 / 84

background image

62 Troubleshooting

Picture / video

No picture is displayed.

Possible causes

Possible solutions

The power cord is not connected. Re-connect the power cord.
The main power switch on the
back of the displayed is not
switched on.

Make sure the power switch is switched on.

The selected input is not
connected.

Depending on the selected input, connect the display with
the input source using the appropriate cable(s).

The display is in Standby mode
when the input source is D-Sub
(VGA).

Check the cable connection. See the user manual for
details.

Incorrect cable connection.

Press any of the control panel (keypad) buttons and check
if the OSD menu could be displayed. If yes, the problem lies
somewhere else.
Try with another display resolution or another graphic card
(GPU).
Restore the display to the default factory settings.

The main board could be
damaged.

Contact the BenQ authorized service partner for
replacement.

Screen interference is observed or noise is heard.

Possible causes

Possible solutions

This could be caused by other
appliances, traffic, or fluorescent
lights in the surroundings.

• Go to

Picture

>

Noise Reduction

.

• Move the display to another location to see if the

interference is reduced.

Poor quality cable is used for
signal input.

Try with another video cable.

The image has a faulty coloration.

Possible causes

Possible solutions

The video cable is not connected
properly.

Make sure the video cable is connected firmly to the
display.

«
...
60
61
62
63
64
...
»

Содержание PH460





















































































Отзывы:

Нет отзывов

Похожие инструкции для PH460

Бренд: Samsung Страницы: 22

GX-20 - Digital Camera SLR

Бренд: Samsung Страницы: 158

Бренд: Samsung Страницы: 100

Бренд: Samsung Страницы: 98

Бренд: Samsung Страницы: 186

Galaxy Camera EK-GC100

Бренд: Samsung Страницы: 178

Galaxy Camera EK-GC100

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 98

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 102

Бренд: Samsung Страницы: 116

BL103 - 10.2 Mega Pixels Digital Camera

Бренд: Samsung Страницы: 98

Бренд: MAGPiX Страницы: 30

Бренд: Loocam Страницы: 8

Бренд: National Instruments Страницы: 41

ATLONA Captivate AT-CAP-FC110

Бренд: Panduit Страницы: 24

Бренд: Omron Страницы: 594

nord stage 2 ha/sw

Бренд: Clavia Страницы: 57

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды