background image

  13

  Positioning your projector

Obtaining a preferred projected image size

The distance from the projector lens to the screen, the zoom setting (if available), and the video format 
each factors in the projected image size.

Projection dimensions

MS560/MX560

• The screen aspect ratio is 4:3 and the projected picture is in a 4:3 aspect ratio

For example, if you are using a 120-inch screen, the recommended projection distance is 5011 mm.
If your measured projection distance is 6200 mm, the closest match in the 

"Projection distance (mm)"

 

column is 6264 mm. Looking across this row shows that a 150'' (about 3.8 m) screen is required.

Screen size

Projection distance (mm)

Offset (mm)

Diagonal

H (mm)

W (mm)

Min distance

Average

Max distance

Inch

mm

(max. zoom)

(min. zoom)

30

762

457

610

1195

1253

1311

45

40

1016

610 

813 

1593 

1670 

1748 

61 

50

1270

762 

1016 

1991 

2088 

2184 

76 

60

1524

914 

1219 

2390 

2505 

2621 

91 

70

1778

1067

1422

2788

2923

3058

107

80

2032

1219 

1626 

3186 

3341 

3495 

122 

90

2286

1372

1829

3584

3758

3932

137

100

2540

1524 

2032 

3983 

4176 

4369 

152 

110

2794

1676

2235

4381

4593

4806

168

120

3048

1829 

2438 

4779 

5011 

5243 

183 

130

3302

1981

2642

5178

5428

5679

198

140

3556

2134

2845

5576

5846

6116

213

150

3810

2286 

3048 

5974 

6264 

6553 

229 

160

4064

2438

3251

6372

6681

6990

244

170

4318

2591

3454

6771

7099

7427

259

180

4572

2743

3658

7169

7516

7864

274

190

4826

2896 

3861 

7567 

7934 

8301 

290 

200

5080

3048 

4064 

7965 

8352 

8738 

305 

250

6350

3810 

5080 

9957 

10439 

10922 

381 

300

7620

4572 

6096 

11948 

12527 

13106 

457 

To optimize your projection quality, we suggest to do the projection within non-gray area.
All measurements are approximate and may vary from the actual sizes. 
BenQ recommends that if you intend to permanently install the projector, you should physically test the projection 
size and distance using the actual projector in situ before you permanently install it, so as to make allowance for this 
projector's optical characteristics. This will help you determine the exact mounting position so that it best suits your 
installation location.

H

W

Projection distance

Center of lens

Screen

4:3 Screen diagonal

Offset

Содержание MH560






















































Отзывы: