Beninca BULLOCK 424 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 12

Beninca BULLOCK 424 Скачать руководство пользователя страница 4

14

Technical Data, dimensions and limits of use

TECHNICAL DATA

BULLOCK

Control unit power supply

230 Vac (Bullock 424)

115 Vac (Bullock 424 115)

50/60 Hz

Motor power supply

24Vdc

Absorbed power

80 W

Absorption

0,6 A

Torque

9 Nm

Operative intermittence

10 minutes ON

50 minutes OFF

Opening speed

10 m/1'

Protection rating

IP44

Functioning temperature

-20°C / +60°C

Driving gear for rack

M4 Z14

Noise

<70 dB

Weight

6,8 kg

DIMENSIONS

Fig. 1 indicates the main clearance dimensions of the gear motor
complete with guide.
The measurements are expressed in millimetres.
If the rack is already present on the gate, it is important to
consider the measurement of the driving gear (89mm), for the
correct coupling between the rack and the driving gear.

If the rack is already present, check that it is well-fixed,
in good state, perfectly horizontal and that the pitch
corresponds to that of the driving gear, M4, i.e. about
12 mm between one notch and the next.

LIMITS OF USE

BULLOCK can be used exclusively for residential sliding gates
with a maximum weight of 400 kg.
Should the gate leaf be heavier than 300 kg, it is recommended
that the braking function be disabled (TSM=0) and the torque
be at its maximum value (PM=0).
The length of the leaf is not a restriction. In all cases it is recom-
mended to install BULLOCK on leaves with length exceeding 6m.

The  materials  with  which  the  door  is  built,  the
state  of  maintenance  and  particular  conditions
of use can reduce the values indicated.
In no case can the installation of BULLOCK be
considered  a  solution  for  opening  inefficient
doors.

295

270

215

Fig.1

120

270

185

89

«
...
2
3
4
5
6
...
»

Содержание BULLOCK 424













Отзывы:

Нет отзывов