SERAPH NT 2.0 QUICK GUIDE
DISPLAY/TONE NOTIFICATIONS
Processing.
An operation is in progress, please
wait.
General failure
. Shown when an operation
fails. E.g. if you try to make a call when there is
no number pre-configured in the device. Simul-
taneously, the
Failure
tone is played.
SIM failure
. Shown when there is no SIM card
inserted in the device, or if the PIN code was
rejected. Simultaneously, the
Failure
tone is
played.
G
ENERAL
NOTIFICATIONS
Battery low
. Shown when there is a need to
recharge the battery (or replace it with another
recharged battery). Simultaneously, the
Battery
low
tone is played.
The device is connected to a charger.
Settings
during battery loading take place. Simulta-
neously, the
Charging
tone is played.
The device is disconnected from a charger.
Settings during battery loading are ended, the
device returns to normal operation.
C
HARGING
NOTIFICATIONS
Normal incoming call
. If available, the name
associated with the calling number/the phone
number itself is shown on the bottom. Shown
until the call is answered (to answer, press
l
).
Initiating information call or position
report
. Press the
l
key and hold it down while
this notification is shown.
Sending a position report.
Simultaneously, the
Message sending
tone
is
played.
Making an information call
. Shown until the
call is answered.
A call is in progress
. Shown while the call is
connected.
N
OTIFICATIONS
REFERRING
CALLS
OR
MESSAGES
Starting emergency cycle
(a long press):
Emergency tone settings are switched on.
Press the BeneGuard button and hold it down
until the wedges are all turned black.
S
TARTING
EMERGENCY
CYCLE
NOTIFICATIONS
(
DISPLAYS
ON
)
Starting emergency cycle
(two quick pres-
ses): Press the BeneGuard button briefly.
Emergency tone settings are switched on.
Press the button again when the second circle
starts blinking.
Emergency cycle cancellation period.
A
countdown timer is shown on the bottom. The
timer counts the cancellation time left (in
seconds). Simultaneously, the
Cancellation
tone
is played. To cancel the emergency cycle, do it
while this notification is shown (by pressing
the
c
key).
Emergency cancellation
. Shown right after
the emergency cycle was cancelled.
Emergency completion
. Shown when the
emergency cycle ends normally, or when the
emergency mode is ended manually.
Emergency call retry.
Emergency numbers
can be voice call numbers. The notification is
shown when the device makes another call
attempt to a number.
Emergency mode/Working
. The device is
through with emergency calls, but sending
messages, message confirmation or position
refresh is still going on.
Emergency confirmation message received
.
After receiving confirmation, the device will
end resending of an emergency message.
Simultaneously, the
Message reception
tone is
played.
"Post-emergency mode"
. The GSM operator´s
name is replaced by the emergency symbol.
While this notification is shown, the device
can be tracked by emergency numbers, also
emergency tone and display settings are kept
on. This mode can be terminated manually, by
pressing the
c
key.
O
THER
EMERGENCY
CYCLE
NOTIFICATIONS
(
DISPLAYS
ON
)
Network emergency call query.
Shown when
the BeneGuard button is pressed but making
emergency cycle is NOT possible (e.g. SIM card is
missing). You can still make network emergency
call by pressing
l
. You can also exit the query
without making an emergency call by pressing
c
.
N
ETWORK
EMERGENCY
CALL
(112, 911)
During the discreet emergency cycle, the device
looks like it is in stand-by mode. The only indicator
of the ongoing emergency cycle is the handset
turned black. When the handset turns white, the
cycle is over (or cancelled). Also tones can be
turned off.
D
ISCREET
EMERGENCY
CYCLE
(
DISPLAY
NOTIFICATIONS
OFF
)
Pre-alarm for sensor alert is NOT set.
Shown
when "the cancel timer" is not configured, and
Emergency cycle starts right away.
To mute the audible alert tone, press the lowmost
side key
y
.
Pre-alarm for sensor alert is set.
The count-
down timer
shows that you still have 28 seconds
time left to cancel the sensor alert if you so
desire.
To cancel the emergency cycle, lift the device to
vertical position. Do it while this notification is
shown.
To let the emergency cycle take place: Do
nothing.
To mute the audible alert tone, press the lowmost
side key
y
.
Alert state ended
. Shown right after the emer-
gency cycle is finished, or the sensor alert is can-
celled.
Post-alarm state
. Shown when the emergency
cycle is completed, and the device makes
audible alarms at regular intervals. You can
receive phone calls and answer them by pressing
l
. In order to stop the post-alarm tone, the
device must be lift up to vertical position.
Alerting of missing sensor
. The device cannot
detect the sensor, and thus it will proceed as fol-
lows: It makes audible alarm and displays notifi-
cation, and then sends an MPTP message (with
status code 112, incl. last position) to the service
center.
N
OTIFICATIONS
REFERRING
SENSOR
ALERTS
00:00.28
