background image

 

RBJ Series of Rolling Bridge Jacks 

22

 

P/N 5900004 — May 2017 — Rev. A 

To maintain hydraulic oil

1.

 

Remove the vented fill cap. 

2.

 

Insert a dipstick or piece of plastic into the tank until it hits the bottom. 

3.

 

Remove the dipstick or piece of plastic and measure the amount of oil. 
The hydraulic oil level should be from 3.35 to 3.5 inches deep. 

4.

 

If the current level is below 3.35 inches, add hydraulic oil until it is above 3.35 inches. 

Troubleshooting 

This section describes how to troubleshoot your product. 

Issue 

Action to Take 

Jack does not lift load. 

Make sure load is not too heavy. 
Make sure jack is getting appropriate air pressure from the air supply. 
Make sure the air hydraulic pump has sufficient hydraulic oil. 
Make sure dirt has not gotten into the hydraulic system. If it has, 

replace the hydraulic oil and clean the hydraulic system. 

Jack does not move along 
utility rail. 

Make sure the utility rail channel and lip are clear of obstructions. 
Make sure jack is correctly situated on utility rail channel or lip. 
Make sure jack is installed on an approved lift. 

Jack raises load but does 

not stay up. 

Make sure you put the jack into a locking position when the load is at 

the desired height. The jack is meant to raise and lower loads; it is not 
designed to hold a load indefinitely if the load is not on a locked 

position. 

If you continue to have an issue, contact your dealer or BendPak Customer Service at (800) 253-2363. 

Warranty 

The BendPak warranty is more than a commitment to you; it is also a commitment to the value of your 

new product. 
For full warranty details and to register your new product, contact your nearest BendPak dealer or visit 

bendpak.com/support/warranty

 

 

Содержание RBJ Series





















































Отзывы: