BendPak LR-10000 Скачать руководство пользователя страница 10

Страница: 10 / 44

LR-10000 Low-Rise Scissor Lift

P/N 5900075 — Rev. A1 — April 2019

Installation Checklist

Following are the steps needed to install your LR-10000 Lift. Perform them in the order shown.

☐

1. Review the installation Safety Rules.

☐

2. Plan for Electrical Work.

☐

3. Make sure you have the necessary Tools.

☐

4. Select the Installation Site.

☐

5. Make sure there is adequate Clearance on all sides of the Lift.

☐

6. Create Chalk Line Guides.

☐

7. Anchor the Bases.

☐

8. Install the Safety Lock Release Handle.

☐

9. Set up the Power Unit Stand.

☐

10. Attach the Power Unit.

☐

11. Connect the Hydraulic Lines.

☐

12. Prepare the Power Unit.

☐

13. Install a Power Disconnect Switch.

☐

14. Install a Thermal Disconnect Switch.

☐

15. Test the Lift.

☐

16. Review the Final Checklist.

☐

17. Leave the Manual for the owner/operator.

Содержание LR-10000












































Результаты поиска

Содержание LR-10000

Отзывы:

Похожие инструкции для LR-10000

Бренды по названию

Популярные бренды

BendPak LR-10000, Инструкция по установке и эксплуатации

Результаты поиска

Содержание LR-10000

Отзывы:

Похожие инструкции для LR-10000

Бренды по названию

Популярные бренды