BendPak HD-12-B Скачать руководство пользователя страница 1

Страница: 1 / 44

INSTALLATION AND OPERATION MANUAL

SHIPPING DAMAGE CLAIMS

When this equipment is shipped, title passes to the

purchaser upon receipt from the carrier.

Consequently, claims for the material damaged in ship-

ment must be made by the purchaser against the trans-

portation company at the time shipment is received.

BE SAFE

Your new lift was designed and built with safety in mind.

However, your overall safety can be increased by proper

training and thoughtful operation on the part of the

operator. DO NOT operate or repair this equipment with-

out reading this manual and the important safety instruc-

tions shown inside.

Keep this operation manual near the

machine at all times. Make sure that

ALL USERS read this manual.

12,000 POUND CAPACITY
COMMERCIAL GRADE
FOUR-POST LIFTS

Models:
HD-12SS-B
HD-12-B
HD-12X-B

PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO

INSTALLATION AND OPERATION. BY PROCEEDING YOU AGREE THAT YOU

FULLY UNDERSTAND AND COMPREHEND THE FULL CONTENTS OF THIS

MANUAL. FORWARD THIS MANUAL TO ALL OPERATORS. FAILURE TO

OPERATE THIS EQUIPMENT AS DIRECTED MAY CAUSE INJURY OR DEATH.

REV F 12-15 -07

1645 Lemonwood Dr.

Santa Paula, CA. 93060, USA

Toll Free 1-800-933-9970

Tel: 1-805-933-9970

Fax: 1-805-933-9160

1800-253-2363

Содержание HD-12-B













































Результаты поиска

Содержание HD-12-B

Отзывы:

Похожие инструкции для HD-12-B

Бренды по названию

Популярные бренды

BendPak HD-12-B, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HD-12-B

Отзывы:

Похожие инструкции для HD-12-B

Бренды по названию

Популярные бренды