BendPak 5175516, Руководство по обслуживанию

Страница: 21 / 32

12
11
14
13
2
10
5
4
8
7
6
1
3
9
15
16
18
17
ISOMETRIC VIEW
FOR REFERENCE ONLY
DO NOT SCALE
REVISION
REV DESCRIPTION DATE EDITED BY ECO#
K
REPLACED 5735772 AND 5735088 WITH
5601262, UPDATED BOM REVISION
05/25/2018 TS 00951
L
ADDD 5735090 AND GLOSS NOTE TO PAINT,
REMOVED GRIT NOTE
12/09/2019 TM 01120
M
REPLACED 5601262 WITH 5735772 AND
5735088, UPDATED WELDING FOR THESE PARTS 03/26/2021
TM 01290
WHERE USED
HD-7PXW
HD-7PXN
HD-7500PBX
ITEM
NO.
PART
NUMBER
DESCRIPTION QTY REV
1 5701050 HD-7PX SERIES POWER SIDE RAMP 1 E
2 5746190 HD-7/7500/9 SERIES RAMP SHEAVE BUSHING 4 C
3 5736170 HD-7-B SERIES CYLINDER CLEVIS 1 A
4 5700192
HD-7PX SERIES, HD-9STX/9SWX/ 9XW/9AE ROLLING BRIDGE BEAM
1 D
5 5735032
ROLLING JACK RAIL CLOSEOUT
2 C
6 5735028 PIN STOP 6 B
7 5701465 HD-7P SERIES DIRECTIONAL SHEAVE BRACKET 2 C
8 5700300 HYD. HOSE HOLDER 2 A
9 5755024 AIR LINE TROUGH Ø13.5 x Ø9.5 x 4064 1 A
10 5755090 HD-7/7500/9 SERIES DRIVE UP RAMP HINGE TUBE 4 C
11 5736202 HD-7/7500/9 SERIES 2-SHEAVE RAMP BOLT PLATE 1 C
12 5736201 HD-7/7500/9 SERIES 2-SHEAVE RAMP END PLATE 1 B
13 5736205 HD-7 SERIES 4-SHEAVE RAMP BOLT PLATE 1 B
14 5736206 HD-7 SERIES 4-SHEAVE RAMP SHEAVE PLATE 1 A
15 5735352 SINGLE CLEVIS CYLINDER ALIGNMENT PLATE 1 A
16 5735772 HD-7 CABLE PLUG ANCHOR PLATE 4 D
17 5735088 HD-7P SERIES ANCHOR PLATE SPACER 2 B
18 5735090 HD-7500/9 SERIES RAMP STRAP 1 C
NEXT ASSEMBLY
5215171 SHEET 1 OF 4
REV DWG. NO.
A
SIZE
TITLE:
NAME DATE
CHECKED
DRAWN
M
1645 LEMONWOOD DR.
SANTA PAULA, CA 93060
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS
THE SOLE PROPERTY OF BENDPAK INC. ANY
REPRODUCTION IN PART OR AS A WHOLE WITHOUT
THE WRITTEN PERMISSION OF BENDPAK INC. IS
PROHIBITED.
AC
5600193
HD-7PX/7500 POWER
SIDE RAMP WELDMENT
11/10/2008
DO NOT SCALE DRAWING
1:30 SCALE:
THIRD ANGLE PROJECTION
OR 03/31/2021
DIMENSIONS ARE IN MM
TOLERANCES:
0. = ±1.5
0.0 = ±0.5
SURFACE FINISH 1.6 ISO Ra µm
FOR MACHINED SURFACES
UNLESS OTHERWISE SPECIFIED
REFER TO MODEL FOR ADDITIONAL INFORMATION 1.
BREAK AND DEBURR ALL SHARP EDGES 0.3mm 2.
REMOVE ALL WELD SPLATTER 3.
DIMENSIONS SHOWN ARE AFTER PAINTING 4.
PAINT GRAY (RAL-7024) 20% GLOSS 5.
NOTE: UNLESS OTHERWISE SPECIFIED.