2-Post Lifts Product Decal Positioning
A
B
BPK Post Lift Decal.pdf
Material: Clear Adhesive PET
Size: 4.25”W x 38”H
Thickness: 4 Mil
Finish: Polished
Ink: U.V. protected, Opaque White
Print Process: Silk Screen, 85 line-screen
(Yellow
color in file represents what should be clear PET
material and SHOULD NOT print as Yellow ink.
White area in file represents Opaque White ink.)
Lamination: Clear-gloss over-laminate for abrasion,
chemical, and ultra violet protection
P/N 5905311
P/N 5905555
Place on BACK of Powerside Post
2-Post Safety Decal.pdf:
Size: 4”W x 28.75”H
Material: White Vinyl Pressure Sensitive
Adhesive
Thickness: 4 Mil
Ink: U.V. protected CMYK 2/C Process
Finish: Polished
Print Process: Offset Lithography - 200 line-
screen or 300 p.p.i. for digital
Lamination: Clear-gloss over-laminate
for abrasion, chemical, and ultra violet
protection
Danger
Warning
Long wheelbase vehicles can damage lift
and/or cause personal harm or injury to
operators if loaded incorrectly.
All vehicles MUST be positioned on lift with
CENTER OF GRAVITY midway between adapters.
Failure to read, understand and
follow these instructions may
cause death or serious injury. Read
and understand these instructions
before using lift.
WIRE ROpE INSpECTION ANd MAINTENANCE
• Lifting cables should be replaced every (3) three years or
when visible signs of damage are apparent. DO NOT USE
LIFT WITH DEFECTIVE OR WORN CABLES.
• Wire rope should be maintained in a well-lubricated
condition at all times. Wire rope is only fully protected when
each wire strand is lubricated both internal and external.
Excessive wear will shorten the life of the wire rope. The
factory suggests wire rope lubricant that penetrates to the
core of the rope and provides long-term lubrication between
each individual strand. In order to make sure that the inner
layers of the rope remain well lubricated, lubrication should
be carried out at intervals not exceeding three (3) months
during operation.
• All sheaves and guide rollers in contact with the moving
wire rope should be given regular visual checks for surface
wear and lubricated to make sure that they run freely. This
operation should be carried out at appropriate intervals
generally not exceeding three (3) months during operation.
For all sheave axles, the factory recommends standard
wheel bearing grease. For all sheaves and/or guide rollers,
the factory recommends 90-WT gear oil or similar heavy
lubricant applied by any method including pump/spray
dispensing, brush, hand and/or swabbing.
NEVER LIFT ANY VEhICLE IN ANY MANNER WITh LESS
ThAN FOUR (4) ARMS. RATEd CApACITY OF EACh
LIFT ARM IS NO GREATER ThAN ONE FOURTh (1/4)
OF ThE OVERALL LIFTING CApACITY.
IMpORTANT
OpERATION / MAINTENANCE
INSTRUCTIONS - pLEASE REAd
TO RAISE LIFT
3
Read Operating and Safety manuals before using lift.
3
Always lift vehicle according to manufacturer’s recommended
lifting points.
3
Position vehicle between columns. Adjust swing arms so that
vehicle is positioned with the center of gravity midway
between pads.
3
Position lift contact pads at manufacturers recommended
lifting points.
3
Use truck adapters as needed. Never exceed 9” of pad/adapter
height.
3
Raise lift by pressing RAISE BUTTON on power unit until contact
pads make contact with the underside of the vehicle.
3
Recheck to make sure vehicle is secure.
3
Raise vehicle to desired working height then press power unit
LOWERING HANDLE until lift carriages rest onto nearest safety
lock position.
3
Maintain visual contact with vehicle and surrounding area at all
times while raising lift.
3
STOP IMMEDIATELY
if load shifts or becomes unlevel.
3
Always ensure safety locks are engaged before any attempt is
made to work on or near vehicle.
3
Always ensure lift contact pads are making full contact with vehicle
before any attempt is made to work on or near vehicle.
TO LOWER LIFT
3
Raise lift by pressing RAISE BUTTON on power unit. Elevate lift at
least two inches to allow adequate clearance for the locks to clear.
3
Clear safety locks by maintaining pressure on SAFETY LOCK
RELEASE HANDLE to its furthest travel.
3
Be sure tool trays, stands or personnel are removed from
under vehicle.
3
Lower vehicle by pressing power unit lowering handle until lift has
descended completely.
3
Maintain visual contact with vehicle and surrounding area at all
times while lowering lift.
3
STOP IMMEDIATELY
if load shifts or becomes unlevel.
3
Before removing vehicle from lift area, position lift arms to provide
unobstructed exit.
3
NEVER, drive over lift arms.
REqUIREd MONThLY MAINTENANCE
3
ALWAYS consult operation manual for factory recommended
maintenance.
3
Check arm restraints for proper operation.
3
Check all chain/cable connections, bolts and pins to insure
proper mounting.
3
Visually inspect safety locks for proper operation.
3
Visually inspect concrete floor. DO NOT USE LIFT if concrete
foundation shows signs of deterioration.
3
Inspect all anchor bolts and retighten if necessary.
3
Check columns for squareness and plumb.
3
Inspect all pivot pins making sure they are properly secured.
3
Check equalizer cable tension – cables must have equal tension -
adjust if necessary.
3
Inspect all lift pads, replace if necessary.
3
If lift is equipped with overhead cut-off switch, check for
proper operation.
WARNING!
1.
WARNING:
If cement anchor bolts are loose, or any component of
the lift is found to be defective,
DO NOT USE LIFT!
2. Never operate the lift with any person or equipment below.
3. Never exceed rated capacity.
4. Always insure safety locks are engaged before any attempt is made
to work on or near vehicle.
5. Never leave lift in an elevated position unless the safety locks
are engaged.
6. Do not permit electric motor to get wet! Motor damage caused by
dampness is not covered under warranty.
CAUTION
BendPak, Inc.® P/N 5905555
USe PrOPer aDaPTerS
Do not attempt to lift trucks or other frame type vehicles
with standard flat contact pads. Frame cradle contact pads
are recommended for use when lifting trucks, vans, or other
frame vehicles. NEVER use lift with missing or damaged
rubber pads. ALWAYS REPLACE rubber contact pads
when worn or damaged. Contact BendPak or your
BendPak dealer for product information.
FRAME CRADLE
CONTACT PADS
Danger
SKU# 5215506
P/N 5905311
1645 Lemonwood Drive
Santa Paula, CA 93060
U.S.A.
(805) 933-9970
www.bendpak.com
Above-Ground Lifts
