BENDIX EC-60 ABS Скачать руководство пользователя страница 47

Страница: 47 / 60

Wheel Speed Sensor Wiring

Route sensor wiring coming out of the wheel ends away

from moving brake components. Sensor wiring needs to

be secured to the axle to prevent excess cable length and

wiring damage. It is required that cable ties be installed

to the sensor wire within 3 inches (76.2 mm) of the sensor

head to provide strain relief.
Following the axle, the sensor wires must be attached

along the length of the service brake hoses using cable ties

with ultraviolet protection and secured every 6 to 8 inches

(152 to 203 mm). Sufficient – but not excessive – cable

length must be provided to permit full suspension travel and

steering axle movement. Install wires so that they cannot

touch rotating elements such as wheels, brake discs or

drive shafts. Radiation protection may be necessary in

the area of brake discs.

FIGURE 19 -

WS-24

™

WHEEL SPEED SEnSOR inSTALLATiOn (S-CAM AnD AiR DiSC BRAkE)

Speed Sensor

Mounting Block

100 Tooth (typical)

Speed Sensor

Exciter Ring

WS-24

™

Speed

Sensor

Hub Assembly

WS-24

™

Speed

Sensor

100 Tooth

Exciter

Ring

Mounting

Block

Max . Gap

(Sensor to Exciter)

.015 Inches

Brake Drum

Bendix does not recommend using standard tie-wraps to

secure wiring harnesses directly to rubber air lines. This

may cause premature wiring failure from the pressure

exerted on the wiring when air pressure is applied through

the air line. Non-metallic hose clamps or bow-tie tie-wraps

are preferred.
The use of grommets or other suitable protection is required

whenever the cable must pass through metallic frame

members.
All sensor wiring must utilize twisted pair wire, with

approximately one to two twists per inch.
It is recommended that wires be routed straight out of a

connector for a minimum of three inches before the wire

is allowed to bend.

90° Speed

Sensors

Straight Speed

Sensors

Sensor

Clamping

Sleeve

Troubleshooting: Wiring

(Continued)

Air Disc Brake

Note:

Ensure that the sensor wiring is

routed to avoid chafing from moving

parts (including rotors and steering

components.)

Содержание EC-60 ABS





























































Результаты поиска

Содержание EC-60 ABS

Отзывы:

Бренды по названию

Популярные бренды

BENDIX EC-60 ABS, Сервисные данные

Результаты поиска

Содержание EC-60 ABS

Отзывы:

Бренды по названию

Популярные бренды