background image

1

®

SD-13-4795

DESCRIPTION

The AR-1

 antilock relay valve (Figure 1) is a specialized

service brake relay valve. It is essentially an R-14

 relay

valve with a special cover that permits direct attachment of
an antilock controller. When combined with an antilock
controller the resulting assembly is referred to as a antilock
relay controller. For example when the AR-1

 antilock relay

valve is combined with the EC-30

 tractor antilock controller

the resulting assembly is referred to as a CR-30

 antilock

relay controller. While intended for use on antilock equipped
vehicles, the AR-1

 antilock relay valve functions solely as

a service brake relay and contains no electronics of its own.

In an air brake system, the AR-1

 valve serves as a relay

station to speed the application and release of the service
brakes. The valve is normally mounted in proximity to the
service actuators it serves. A mounting bracket furnished

with the valve permits either frame or cross member mounting.
All air connections on the AR-1

 valve are identified with

cast, embossed letters for ease of installation. The letter
identification and air line connections are shown below for
reference.

AR-1

 VALVE

AIR CONNECTION

EMBOSSED IDENT.

Supply (to reservoir)

SUP

Delivery (to brake actuator)

DEL

Service (to brake valve rear service delivery)

SER

Like the R-14

 relay valve, the AR-1

 valve incorporates a

quick release valve adjacent to the service port which provides
for rapid exhaust of control air pressure from above the

Bendix

®

 AR-1

 AntiLock Relay Valve

FIGURE 1 - AR-1

 ANTILOCK RELAY VALVE ASSEMBLY

EXHAUST PORT

SERVICE PORT

QUICK EXHAUST

DELIVERY PORTS

SUPPLY PORT

TYPICAL

MOUNTING

BRACKET

SUPPLY PORT

EXHAUST PORT

DELIVERY

PORT

QUICK

EXHAUST

INLET/

EXHAUST

VALVE

RELAY

PISTON

SERVICE

PORT

QUICK/

EXHAUST DIA.

ANTILOCK

CONTROLLER

AR-1

ANTILOCK

RELAY VALVE

AR-1

 VALVE

WITH ANTILOCK

CONTROLLER

Содержание AR-1 ANTILOCK RELAY VALVE









Отзывы: