background image

3

Danger indicates a hazardous situation that, if not avoided, will result 

in death or serious injury.

Warning indicates a hazardous situation that, if not avoided, could 

result in death or serious injury.

Caution indicates a hazardous situation that, if not avoided, may result 

in minor or moderate injury or property damage.

Notice indicates important or helpful information and/or user tips.

SAFETY WARNING KEY

PRODUCT SPECIFIC SAFETY WARNINGS

>  To avoid serious injury, keep hands and fingers away from 

  spinning router bit. Maintain awareness of the bit at all times.

>  NEVER FEED YOUR WORKPIECE 

  BETWEEN THE BIT AND THE 

 FENCE. Because of the direction 

  of the bit’s rotation, the bit could 

  “grab” the workpiece and propel it 

  away from the table at a high velocity, 

  potentially resulting in property 

  damage and serious injury to 

  anyone in its path. 

>  Additionally, when the bit grabs the 

  workpiece, your hands could be drawn 

  into the bit, resulting in serious injury.

AVOID THIS SITUATION!

Product Specific Safety Warnings continued on page 4

Fence

Workpiece

Bit Rotation

Feed Direction

>  Turn off and unplug your router before 

  installing or adjusting the bit or adjusting 

  the Router Table Fence.

>  BEFORE beginning any routing 

 operation, 

ALWAYS make sure that 

  ALL knobs on the Router Table Fence 

  have been tightened and the fence 

  will not shift during use.

Содержание PROFENCE













Отзывы: