Benassi FT 530 Скачать руководство пользователя страница 8

  

S.p.A.                                                                                       

FT 530- FT 533 

 

 

FREE WHEEL BLOCKING 
 

  The wheels are blocked through two rings at both ends of the transmission shaft. One of these rings is 

provided with a pivot and can be fixed in two different positions: 

 

Pivot position towards the outside (picture D)

: in this position the wheel is free to turn, this produces a 

differential effect and helps the machine while moving forward in a curve. 

 

Pivot position towards the inside (picture A)

: in this position the wheel is blocked to the shaft so that the 

differential effect is lost. In this way, however, if the machine moves on a downhill ground it follows the throttle 
control without getting an exaggerate speed. 

 

To change the position of the ring it is necessary to unscrew the bolt and then screw it tight again till it is 
completely blocked (pictures B+C). 

 
 

 

   

 

 
  

     

 

  

  

 
 ADJUSTMENT OF THE TRANSMISSION BELT. 

1.  After unscrewing the 4 screws, remove the front guard ( Pos. B in Pict.6). 
2.   Loosen the nut Pos .C in Pict. 7, using a spanner size 17, and let the screw supporting the belt-tightener ( pos. B 

in Pict.7), until the belt is properly tight.

  

3.  Block again the Nut ( Pos. C in Pict 7) in the correct position 
The adjustment of the belt-tightener should be regularly done, and the transmission belt should be always perfectly 
aligned, and tight.  

  For the adjustment of the driving levers on the handlebar, and the relative cables, please check the second 

Chapter “ PACKING AND ASSEMBLING”.  

  For mowing very high and strong grass, you can remove the side conveyor (Pos.A in Pict.8), and also the front 

guard (Pos. B in Pict.8), after unscrewing the fixing screws. Before doing this job, please make sure that the engine 
is off, and the spark plug disconnected.  

 

IMPORTANT !  The operator must be aware that the machine at work could throw out stones and other 
dangerous things. He should always make sure that the working area is free, for a minimum radius of 50 
metres in any direction .It is recommended to delimit the working area with safety stripes,and signals of 
danger. 

 

Foto C

Foto D 

Foto A 

Foto B 

Содержание FT 530













Отзывы: