Belltech 6519 Скачать руководство пользователя страница 1

6519-888 9/05 

 

A Division of KW AUTOMOTIVE North America, Inc. 

 

 

INSTALLATION INSTRUCTIONS 

----3

300 W. Pontiac Way Clovis, CA 93612     toll free: 1-800-445-3767      web: www.belltech.com

---- 

 

 

6519 

REAR AXLE FLIP & HANGER KIT 

04-UP CHEVROLET 1500 QUAD CAB 

 

 

Thank you for being selective enough to choose our high quality BELLTECH PRODUCT.  We 

have spent many hours developing our line of products so that you will receive maximum 

performance with minimum difficulty during installation. 

 
Note:  

Confirm that all of the hardware listed in the parts list is in the kit.  

Do not

 begin installation if 

any part is missing.  Read the instructions thoroughly before beginning this installation. 

Warning

DO NOT

 work under a vehicle supported by only a jack.  Place support stands securely under 

the 

vehicle in the manufacturer’s specified locations unless otherwise instructed. 

Warning

DO NOT

 drive vehicle until all work has been completed and checked.  Torque all hardware to 

values specified. 

Reminder: 

Proper use of safety equipment and eye/face/hand protection is absolutely necessary when 
using these tools to perform procedures! 

Note: 

It is very helpful to have an assistant available during installation. 

 

RECOMMENDED TOOLS: 

 

  Properly rated floor jack and six (6) support stands 

  Wheel chocks 

  Die grinder equipped with abrasive cut-off wheel 

 

½” drive torque wrench 

  Standard socket wrench set 

 

Air powered ½” drive impact wrench 

  Flat bladed screw driver 

  Safety glasses 

  Air powered chisel 

 

KIT INSTALLATION 

 

As this is a relatively involved installation, 

we recommend

 that a qualified mechanic at a properly equipped 

facility  perform  it.   

We  also  recommend

 that  the  installation  be  performed  on  a firm, flat  and  level  surface, 

such as seasoned asphalt or concrete.  The use of safe and properly maintained equipment is very important!  
In  order  to  document  any  possible  irregularities  in  the factory  ride  height  of  your  vehicle,  please  take  a few 
moments  to  fill  out  the

  Belltech  Vehicle  Inspection  Record

  included  with  these  instructions.   

We  also

 

recommend

 measuring and recording all stock driveline angles prior to installing this kit. This information may 

be helpful if vibration problems arise after installation. 

 
 
 
 
 
 

Содержание 6519











Отзывы: