background image

A: Install against wall 

1. 

Using a spirit level mark a vertical centre line on the wall where the hood is to be positioned, and a horizontal
line where the hood base will be.

NOTE: The distance from the horizontal line to an electrical cooktop underneath must be minimum 

of 600mm & 650mm Free space to a gas cooktop and a maximum height of 750mm. 

*If the instructions of the hob specify a greater distance than the minimum above, then that shall be the minimum height for installation

2. 

Drill 4 holes of 8mm diameter on the wall according to below drawing.

3. 

Hammer 

dry wall anchor plugs 

into holes. Insert 2pcs 

Screw(ST4x30mm) 

into the two lower holes(with distance

to horizontal line 496mm 60cm & 795mm 90cm) and fasten, they will be used to hang on the range hood.

Warning: Failure to install the screws or fixing device in accordance with these instructions may result in 
electrical hazards 

Vertical centre line 

Where the range hood will be 

Horizontal line 

Hood base 

Minimum: 

Electric 600mm  Top of Cooktop 
Gas 650mm  Top of Trivet 

Maximum: 

750mm 

Vertical centre line 

516mm 

496mm For CRHR6W01&  795mm For BRA903SLX 

190mm 

152mm 

Horizontal line 

Hood base 

Содержание BRA903SLX
















Отзывы: