Belleco 204000 Скачать руководство пользователя страница 2

Page 1 

OPERATIONS AND MAINTENANCE PROCEDURES 

CONVEYOR TOASTER MODELS 

JT3TW 

 

UNCRATING AND INSPECTION

 

 
Unpack the unit and components from the shipping container. Remove all visible packing 
materials including those that may be inside the toasting chamber. If damage is discovered, file a 
claim immediately with the carrier that handled the shipment. 
 

ASSEMBLY AND INSTALLATION 

 
The toasters are shipped fully assembled and ready to plug into a matching outlet specified for its 
specific voltage and amperage rating. Removal or replacement of the power cord and plug will 
VOID the warranty. For assistance, contact the Belleco, Inc. Service Group at 1-877-854-8006. 
Please refer to the appropriate schematic at the rear of this manual for plug configurations. 
Consult with a licensed electrician prior to installation. 

"

Do not operate the toaster without the 

crumb tray properly installed as this may cause overheating and loss of productivity. 
 

 

CAUTION – During installation: Do not place on surfaces or near walls, partitions or 

kitchen furniture and the like – unless they are made of non-combustible material or clad with 
non-combustible heat-insulating material, and pay attention to fire prevention regulations.

  

 

CAUTION – To reduce the risk of fire, the appliance is to be installed in non-

combustible surroundings only, with no combustible material within 18 inches of the sides, front, 
or rear of the appliance or within 40 inches above the appliance. "Bread may burn. Therefore 
toasters must not be used near or below curtains and other combustible materials. They must be 
watched." 

 

"Le pain peut bruler, aussi les grille-pain ne doivent-ils pas etre utilizes a proximite ou sous des 

rideaux ou autres materiaux combustibles. Ils doivent etre suveilles." 

 

ELECTRICAL INSTALLATION 

 

  WARNING – Disconnect the toaster from its power source before installing or removing 

any parts. 
 

  WARNING – Check with your local power company or licensed electrician before 

installation to determine the actual voltage at the outlet. For a toaster rated 208 volts, never plug 
it into 240 volts as serious overheating and damage could occur. For a toaster rated 240 volts, 
never plug it into 208 volts as the lower voltage will greatly reduce the productivity of the unit. 
 

  WARNING – NEVER operate any piece of equipment without proper GROUND 

connection. Improper grounding may result in serious personal injury or could be fatal! 
 
 

Содержание 204000








Отзывы: