Bell and Gossett NBF-25 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 20

background image

Product Description

General description

The NRF/NBF circulator pump has these features:

• System liquid lubricated bearings
• Non-overloading permanent split capacitor motor with thermal or impedance

protection

• Quiet operation
• Nonsubmersible

Pump application

WARNING:

California Proposition 65 warning! This product contains chemicals known to the state of
California to cause cancer and birth defects or other reproductive harm.

You can use this pump for these types of applications:

• Water circulating applications in hydronic and solar systems.
• Indoor use only

Do not use in swimming pools and marine areas.
Xylem recommends that you use bronze or stainless steel booster pumps for pumping
potable water. For other applications, contact your local Xylem representative.

Operational specifications

These pumps are designed to pump liquids compatible with their iron or bronze body
constructions.

Operational Limits

Parameter

Value

Maximum operating pressure

150 PSI (10 bars)

Maximum operating temperature

225˚F (107˚C)

Electrical Rating

115V, 60Hz, 1Ø; 230V, 60Hz, 1Ø (single phase power)

Product Description

8

NRF

™

-25,36,45/NBF

™

-25,36, and 45 Circulator Installation, Operation, and Maintenance Manual

«
...
7
8
9
10
11
...
»

Содержание NBF-25





















Отзывы:

Нет отзывов

Похожие инструкции для NBF-25

Бренд: Gardena Страницы: 17

Бренд: Samsung Страницы: 27

Бренд: Zoeller Страницы: 10

Бренд: Daikin Страницы: 26

Бренд: Rowi Страницы: 40

Exubera Pro UC EV9333-50

Бренд: Everpure Страницы: 2

Бренд: Noritz Страницы: 120

BTR(C)120 THRU 500A

Бренд: A.O. Smith Страницы: 36

Бренд: Lumax Страницы: 28

Бренд: Okay Страницы: 52

S3C1-E6.2 230/3

Бренд: GORMAN-RUPP PUMPS Страницы: 51

Бренд: Lampoassa Страницы: 62

Бренд: Uni-max Страницы: 6

Бренд: TOHATSU Страницы: 99

Бренд: NAKAYA Страницы: 47

Бренд: Alpha Страницы: 15

Бренд: Graco Страницы: 20

Бренд: Laars Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды