Laser Printer
INTRODUCTION
Thank you for purchasing a Belkin Uninterruptible Power
Supply (UPS). Each year, several natural and man made
occurrences put the power supplied to your electronics in
your home or office in jeopardy. At risk are your hardware,
software and data because of these power problems.
IMPORTANT SAFETY INSTRUCTIONS
Please save this manual!
It contains important operating instructions and warranty
information pertaining to your UPS.
Please save or recycle the packaging materials!
The UPS packaging was designed with great care to provide
protection during shipment and delivery. These materials
are invaluable if you ever have to return the UPS for service.
Damage sustained during transit is not covered under the
warranty.
Federal Communications Commission Interference
Statement
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. To assure continued
compliance, use only shielded interface cables when
connecting to computer or peripheral devices. Any changes
or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate this equipment.
CONTENTS
You should have received the following:
1 – UPS unit
1 – Bulldog Plus Shutdown Software
1 – USB Cable
1 – Serial Cable
1 – Phone Line Cable
1 – Coaxial Cable (only F6B900-UNV)
UPS FEATURES AND FUNCTIONS
Your UPS features 3 LED indicators which specific’s certain
functions on your UPS. Please review the Front Panel
diagram and with this chart, as it will assist you in the use of
your UPS.
Indicator Condition
Meaning
О
Solid Green
AC Power is on
ON LINE
(Green LED)
☼
Flashing Green
AVR is active
ON BATTERY
(Yellow LED)
☼
Flashing Yellow
LED with Audible
Alarm (Beeping)
This condition for the
On-Battery LED can indicate 1
of 2 problems:
1. The UPS is on battery
backup and an intermittent
audible alarm is on. The UPS
will begin shutdown
procedure.
2. Battery is low. The UPS will
start shutdown. The buzzer
sounds an audible alarm.
○
Solid Red
The Fault/Overload can
indicate 1 of 2 problems.
1. There is a problem with
the UPS. The LED will be
lit continuously, and the
unit will sound an audible
alarm for 10 seconds.
2. Battery is weak or bad; the
battery needs to be
replaced.
FAULT/
*OVERLOAD/
*Replace
Battery
(Red Led)
☼
Flashing Red
Battery output is drawing
more power than the UPS
can provide.
SITE WIRING
FAULT
(ON REAR PANEL
)
○
Solid Red
There is either no ground
circuit or a reversed polarity
in the building wiring.
BATTERY REPLACEMENT PROCEDURE
Replacement requires removing the battery cover plate on
the back or bottom of the UPS. No tools are needed. To
replace the batteries:
1. Press fastener to remove the battery cover plate on the
back of the UPS (Fig. 1).
2. Disconnect the insulated connectors from the battery
terminals (Fig. 2).
3. Remove the battery then insert a new battery pack,
and push the connectors onto the battery terminals
(black to black & red to red) (Fig. 3).
NOTE:
There may be a small spark at the battery
terminals when reconnecting the connectors. This is
normal and will not harm you or the UPS.
4. Close the battery cover (Fig. 1).
Fig. 1 Fig. 2 Fig. 3
ALARMS
BATTERY BACK UP (Slow Alarm)
When in the UPS is in battery BACK-UP mode, the On Battery
(Yellow LED) illuminates and the UPS sounds an audible alarm. The
alarm stops when the UPS returns to normal ON LINE operation.
LOW BATTERY (Rapid Alarm)
When the UPS is in battery BACK-UP mode and the battery energy
begins to run low, the UPS will beep rapidly until it shuts down from
a depleted battery or returns to ON LINE normal operation.
OVERLOAD (Continuous alarm)
When the UPS is overloaded (the connected loads exceed the
maximum rated capacity), the UPS emits a continuous alarm to
warn of an overload condition. Disconnect nonessential equipment.
from the UPS to eliminate the overload.
FAULT (10 Seconds Continuously)
When the UPS occur fault, the UPS emits a 10 seconds continuous
alarm to warn of a fault condition. Disconnect the equipment from
the UPS prior to checking the equipment.
TOP & REAR PANEL
TOP PANEL
REAR PANEL
A
、
SURGE-ONLY PROTECTED OUTLETS
Equipment such as a printer, fax machine, scanner, or a desk
lamp can be plugged into these outlets. These outlets do not
provide power during a power outage. These outlets are always
on (when AC power is available) & are not controlled by the
front panel switch.
Note:
Only for F6C900-UNV-PL Model, these 2 outlets are
HomePlug network-compatible Outlets, they are designed to
work with HomePlug networking equipment.
Plug a HomePlug adapter (sold separately) into your
HomePlug network-compatible Outlet.
B
、
BATTERY BACK UP OUTLETS
Only data sensitive equipment such as a computer, monitor and
external drive should be plugged into these outlets. Battery
power is automatically provided in case of a power outage.
Power (AC or battery) is not supplied to these outlets when the
UPS is switched off. (Do not plug surge protectors or power
strips into the battery back up outlets).
C
、
PHONE/FAX/ MODEM PROTECTION
The phone/fax/modem lines are surge protected and provide
complete safety for line connection.
D
、
INTERFACE PORTS (USB & RS232)
The UPS provides both a USB and RS232 port for use with
your computer.
NOTE: Choose one port only.
E
、
AC INPUT BREAKER (CIRCUIT BREAKER)
The circuit breaker button will be triggered if an overload
condition forces the UPS to disconnect itself from utility power.
If the button sticks out, disconnect nonessential equipment and
depress breaker.
F
、
AC INPUT POWER CORD
G
、
SITE WIRING FAULT INDICATOR
The Site Wiring Fault LED will illuminate when one of the
following conditions exist:
1.
Open or high-resistance ground
2.
Hot and neutral polarity reversal
3.
Overloaded neutral circuit
H
、
AUDIO/ VIDEO SURGE PROTECTION PORT
(Only F6B900-UNV)
I
、
NETWORK PROTECTION
This connector is used for protecting the transmission line of
Ethernet card from surge, noise and spike.
INSTALLATION
Note!
Before installation, please inspect the UPS Upon
receipt. Make sure that the UPS is not damaged.
Connect to AC Utility Power
Connect the AC inlet to utility power via the power
cord. Check whether the Site Wiring Fault indicator
is lit or not. If so, please check the utility wiring.
Charging the Battery
For best results, charge the battery for 8 hours prior to initial
use. The UPS charges its battery whenever it is connected to
the utility power.
Plug in Power Devices
Plug your devices into the AC outlets on the top of the UPS. To
use the UPS as a master on/off switch, make sure all of the
loads are switched on.
Caution: Never connect a laser printer or
scanner to the backup outlets of UPS with
other computer equipment. A laser printer
or scanner draws significantly more power
when in use than when idle. This may
overload the UPS.
Turning on the UPS
Turn on your UPS by pressing and holding the On/Off/Test
button for approximately 2 seconds until the “ON LINE” Green
comes on.
Turning off the UPS
Turn off the UPS by pressing and holding the On/Off/Test
button for more than 2 seconds until the “ON LINE” or “ON
BATTERY” LED goes off.
To Conduct a Self Test
Use the self-test to verify both the operation of the UPS and
the condition of the battery. In normal utility power, push the
On/Off/Test button less than 1.5 seconds and the UPS
performs a self-test function. During the self-test, the UPS
operates in back-up mode.
Note! During the self-test, the UPS briefly operates on-
battery backup power (the on-battery LED comes on). If
the UPS passes the self -test, it returns to on-line
operation. If the UPS fails the self-test, it immediately
returns to on-line operation and lights the replace battery
LED. The loads are not affected. Recharge the battery
overnight and perform the self- test again. If the replace
battery LED is still on, the battery will need to be
replaced.
To Silence Audible Alarm
While in battery BACK-UP mode, push on/off/test button less
than 1.5 seconds to silence the audible alarm. (This does not
work if the UPS is under LOW BATTERY or OVERLOAD
condition.
All equipment must be turned off prior to hardware installation.
Connect the phone/ fax/ modem/ lines
Connect a single phone/ fax/ modem line into the
surge-protected sockets on the back of the UPS. The RJ-11
modular sockets accepts standard single line telephone
connections. The connection will require another length of
telephone cable, which is supplied.
Note!
This connection is optional but highly suggested as
phone/ fax/modem lines often carry dangerous surges and
spikes. The UPS works properly without a phone/ fax/ modem
connection.
Caution!
The phone/ fax/modem protection feature could be
rendered inoperable if improperly installed. Make sure that the
telephone line from the wall is plugged into the connector
marked “IN”, and the device to be protected is plugged into the
connector marked “ OUT”.
SYSTEM REQUIREMENTS
The UPS can be used without the software and can be used
with any computer using a monitor or a flat panel screen. Also,
you do not have to have the software installed to utilize the
battery backup outlets.
To fully utilize the UPS and its software, your computer must
be able to operate the following operating systems: 95/ 98/
ME/ NT4/ 2000/ 2003/ XP & Linux & Higher and have a Serial
or USB port.
SERIAL OR USB COMMUNICATION PORT
(INSTALLATION OPTIONAL)
To fully utilize the Bulldog Plus Shutdown Software; you will
need to connect the UPS to your computer.
The communication port will provide the following features:
1. Monitoring charger status
2. Monitoring UPS status
3. Monitoring battery status and condition
4. Monitoring
the utility status
5. Use the ON/OFF/TEST UPS power switch function to
schedule UPS for power saving
FOR MODEL
F6B900-UNV
F6C900-UNV
F6C900-UNV-PL
F6C1100-UNV
○
R
ON/ OFF/ TEST
ON LINE
ON BATTERY
FAULT/
* OVERLOAD/
* REPLACE
BATTERY
Wiring Fault
IN
cautionary marking
Refer to bottom for
Protection
IN
Push to Reset
AC Input
OUT
Network
OUT
Breaker
Circuit
RS-232
Site
IN
OUT
Phone/Fax/Modem Protection
OUT
F
C
D
E
G
H
I
IN
Breaker
Circuit
RS-232
Push to Reset
Phone/Fax/Modem Protection
Wiring Fault
OUT
IN
OUT
Telephone Socket
Phone/ Fax/ Modem
A
B
Surge Protection Only
1100 VA
Battery Back-up + Surge Protection
