Belanger Gyro Wrap Signature Series, Руководство пользователя

Страница: 6 / 88

CURRENT REVISION LOG
Belanger, Inc. * PO BOX 5470 *Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681
1MANUL248
Rev
Release
Date
Page Description
40
Under Pneumatic Connections removed Passenger Side from step 4c
Changed “4 wire electrical cord” in Note to “4 conductor cable”
Under Electrical Junction Box Connections step 1 changed electrical to electrician and in
step 1c removed Passenger Side:
41
Updated the image of the distribution manifold in Step 2 of Electrical Junction Box
Connections
Removed the first word “Supplies” from the first paragraph of the Electrical Motor/Gearbox
Connections section
Added images to Electrical Motor/Gearbox Connections step 1 and in step 2 changed 4
wires to 4 conductor cable
Replaced “If you have the optional motor covers, you will need to…” with “Then…”
42
Changed “wired up” to “connected” in the first sentence under Wheel Rotation
Changed the sentence: Use the image for... to Refer to the image at the bottom of this
page for…
Changed “Turn power off swap motor leads if necessary.” to “If the wheels are rotating
incorrectly turn the power off and swap the motor leads.”
Corrected typo in Note: show to shown
Removed Water Manifold Installation section under Utilities; manifold ships secured in
position
43 Added Connecting the Hydraulic Hoses instructions and images under Utilities section
45 Changed filler strip part numbers: 8812 to 9317 and 8805 to 9310
46
Changed filler strip lengths: at base of frame legs from 7-3/4” to 7-7/8” in four places, on
top of the head assembly from 67-13/16” to 15-1/16”, on top of the passenger side arm
assembly from 43-1/4” to 33-1/2” and added a 7-3/4” filler strip
48
Removed the third sentence in the first paragraph under Swing Flow Control which stated:
On each stand, there are two such controls.
50
Removed and added Daily, Weekly and Monthly Routine Procedures
Removed Quarterly Routine Procedures
50-52 Added the Powder Coating Maintenance and Powder Coating Repair Procedures
55 Added exploded views of the Head Assembly with Hydraulic Lines
56 Added exploded views of the Arm Assemblies with Hydraulic Lines
57
Changed part numbers: 1BERNG810 to 1BERNG849 in two places, 1GRMIT750 to
1GRMIT666, 8767 to 9298 and 8778 to 9299
Corrected part number: 1WASHR-LC281 to 1WASHR-LC581
58
Removed Hydraulic from the first subheading on the page
Changed second subheading from Gyro Head Assembly: Hydraulic to Gyro Cylinder
Assembly: 109721 & 109722
59
Changed subheading from Gyro Head Assembly: Hydraulic to Gyro Cylinder Assembly:
109721 & 109722
Changed subheading from Posi-Stop Mount Assembly: 109722 to Gyro Cylinder
Assembly: 109721 & 109722
Changed part number 1VALVE-HY393 to 1VALVE-HY395 (per Change Request #11)
60
Added exploded views of the electrical and hydraulic distribution manifolds
Added “see below” to component callouts
Added 109712 and 109713 to subheading and component callouts
61
Added 60 Hz into the following subheading Gyro Head Assembly: Electric 60Hz (Upper
Section)
Added the number 1 to all the plastic gear cover part numbers in chart
62
Replace with a new exploded assembly to include the 1FSTNR-SH958(4) fasteners
Corrected part numbers: 8781 was 3211, 1BERNG849 was 1BERNG810 (2 places), 8783
was 8738,
63
Added this page to show the exploded view of the Gyro Head Assembly for the 50 Hz
electric motor, drive shaft and assembled image