Bel Canto SET 80 Скачать руководство пользователя страница 10

Страница: 10 / 11

Page 10

SET 80

Owner's Manual

Specifications

Continuous power output into 4 or 8 ohms • 70 watts

Peak power output • 140 watts

Bandwidth • -3 dB 6 Hz - 35 kHz

Class of operation • Class A single-ended balanced 845 triode

Input level for 70 watts output • 2 Vrms

Signal to Noise Ratio re 1 watt out • 100 dB A weighted

Distortion at 1 watt / 1 kHz • <0.05% predominantly 2nd harmonic

Damping Factor • 3 across full bandwidth

Input configuration and impedance • 100K ohm single ended/balanced

Gain at 8 ohm tap • 18 dB

Power Requirement • 110-120 / 220-240 VAC; 50-60 Hz

• 400 VA per chassis

Voltage settings are made at our facility to correspond to requirements of the country in

which the product is shipped.

Size • 19.5" W x 15" D x 11" H each (496 mm x 381 mm x 280 mm)

Weight • 85 lbs each (39 kg)

Service

Under normal operation the fuse should not need replacing. There is one standard 1/4" x 1" fuse.
Remove the power cord before changing the fuse. Contact your dealer if assistance is needed.

Содержание SET 80












Результаты поиска

Содержание SET 80

Отзывы:

Похожие инструкции для SET 80

Бренды по названию

Популярные бренды

Bel Canto SET 80, Руководство пользователя и эксплуатационная информация

Результаты поиска

Содержание SET 80

Отзывы:

Похожие инструкции для SET 80

Бренды по названию

Популярные бренды