manualshive.com logo in svg

Bel Canto orfeo 60, Руководство пользователя и эксплуатационная информация, Страница: 10 / 11

Поделиться
Скачать
Bel Canto orfeo 60 Скачать руководство пользователя страница 10

 

 
  

Page 10 

Orfeo 60

 Owner's Manual

 

Specifications

 

 
 
 

Power output into 4 or 8 ohms • 60 watts 

Bandwid

th • -3 dB  6 Hz - 33 kHz 

Class of operation • Class A single-ended balanced 845 triode 

Input level for 30 watts output  • 150 mV rms 

Signal to Noise Ratio re 1 watt out • 100 dB A weighted  

Distortion at 1 watt / 1 kHz • <0.05% predominantly 2nd harmonic 

Damping Factor • 3 across full bandwidth 

Input configuration and impedance • 100K ohm single ended/balanced 

Gain at 8 ohm tap • 20 dB 

 

Power Requirement • 110-120 / 220-240 VAC; 50-60 Hz 

 

• 400 VA per chassis 

 

Voltage settings are made at our facility to correspond to requirements of the country in which 

the product is shipped.

 

 

Size • 19.5" W x 15" D x 11" H each (496 mm x 381 mm x 280 mm) 

Weight • 80 lbs each (36.3 kg) 

 
 
 

Service

 

 
Under normal operation the fuse should not need replacing. There is one standard 1/4" x 1" fuse.  
Remove the power cord before changing the fuse. Contact your dealer if assistance is needed. 

Содержание orfeo 60












Отзывы:

Нет отзывов