background image

 CAUTION

To avoid risk of injury, or 

product or property damage:

•  Use two or more people or 

suitable lifting device when lift-

ing appliance.

•  Remove and discard all pack-

ing materials, including card-

board and tape on the outside 

and inside of the range.

•  Remove any plastic protective 

wrap on all parts.

•  Thoroughly wash the interior 

with hot, soapy water, rinse, 

and wipe dry.

•  Dispose of all packing materi-

als according to environmental 

standards.

•  Check for possible shipping 

damage immediately after re-

ceipt. If the oven is found to be 

damaged, contact your point of 

sale immediately.

•  DO NOT

 connect and operate 

the oven if any damage was 

found.

Note the time, date, and who 

was spoken to, and follow up and 

confirm with written or electronic 

communication.
All original packing materials must be 

kept for inspection purposes.

6.3  BEFORE INSTALLATION

The appliance is intended for 

installation in commercially available 

kitchen cabinets and a minimum 

clearance must be ensured between 

the appliance and kitchen walls, 

floors, and furniture for safety. 
•  Surfaces, synthetic laminates, and 

adhesives used near or around the 

unit must be heat resistant.

•  Kitchen cabinets used for installa-

tion must be set level and fixed in 

place.

•  All openings in the wall behind the 

oven and in the floor under the 

oven must be sealed.

•  Drawings used in this manual 

are representational and may not 

match each appliance exactly.

•  Product guarantee is valid after 

proper installation. The manufac-

turer will not be responsible for any 

hazard or damage resulting from 

improper installation or use.

•  Always carry the appliance using 

two or more people. Do not drag 

the appliance across any surface, 

as this may damage the surface.

•  Remove all shipping materials 

inside and outside of the oven.

•  Remove all equipment from inside 

the oven, including the oven racks 

and printed documents.

•  Read manual before installing ap-

pliance.

•  The California Safe Drinking Water 

and Toxic Enforcement Act re-

quires the Governor of California to 

publish a list of substances known 

INSTALLATION

16

Содержание WOS30200SS

























Отзывы: