background image

10 / EN

Washing Machine / User‘s Manual 

3

 Installation

To make the product ready for use, review the 

information in the user manual and make sure 

that the electricity, tap water supply and water 

drainage systems are appropriate. If they are 

not, call a qualified technician and plumber to 

have any necessary arrangements carried out.

C

Preparation of the location and 

electrical, tap water and waste 

water installations at the place of 

installation is under customer's 

responsibility.

Make sure that the water inlet and 

discharge hoses as well as the power 

cable are not folded, pinched or 

crushed while pushing the product 

into its place after installation or 

cleaning procedures.

B

WArNING: 

Manufacturer shall not 

be held liable for damages that may 

arise from procedures carried out by 

unauthorised persons.

A

WArNING:

 Prior to installation, 

visually check if the product has any 

defects on it. If so, do not have it 

installed. Damaged products cause 

risks for your safety.

3.1 Appropriate installation location

•  Place the machine on a rigid floor. Do not 

place it on a long pile rug or similar surfaces.

•  Total weight of the washing machine and the 

dryer -with full load- when they are placed 

on top of each other reaches to approx. 180 

kilograms. Place the product on a solid and 

flat floor that has sufficient load carrying 

capacity!

•  Do not place the product on the power cable.

•  Do not install the product at places where 

temperature may fall below 0ºC.

•  Place the product at least 1 cm away from the 

edges of other furniture.

3.2 removing packaging 

reinforcement

Tilt the machine backwards to remove 

the packaging reinforcement. Remove the 

packaging reinforcement by pulling the ribbon.

3.3 removing the transportation 

locks

A

WArNING: 

Do not remove the 

transportation locks before taking 

out the packaging reinforcement.

WArNING: 

Remove the 

transportation safety bolts before 

operating the washing machine! 

Otherwise, the product will be 

damaged.

1. Loosen all the bolts with a suitable spanner 

until they rotate freely

 (C)

.

Содержание WMB91633LW









































Отзывы: