Beko din28r20 Скачать руководство пользователя страница 12

Страница: 12 / 45

Dishwasher / User’s Manual

/43 EN

Installation

drainage. The length of this connection

must be min. 50 cm and max. 100 cm from

the floor. A discharge hose longer than 4

meters will cause washing performance

to be affected.Attach the water discharge

hose to the drainpipe without bending

it. Tightly fix the water discharge hose

to the drainpipe in order to prevent any

dislocation of the water discharge hose

during operation of the product.

min 300

min 120

max 1000

min 500

Drainpipe must be connected

to the foul water system and it

should not be connected to any

surface water drain.

Adjusting the feet

If the door of the product cannot be closed

properly or if the product wobbles when

you push it slightly, then you need to adjust

the feet of the product. Adjust the feet of

the product as illustrated in the relevant

section.

Electrical connection

Before you insert the plug into the wall

socket make sure that the voltage and

the frequency shown in the rating label

corresponds to your electricity supply.

We recommend that this appliance be

connected to the mains supply via a

suitable switched and fused socket in a

readily accessible position.

If the supply cord or the mains lead is

damaged please do not replace it yourself.

The supply cord or the mains lead must be

replaced by a Authorised Service Agent or a

similarly qualified person.

This appliance must

be earthed

If the fitted moulded plug is not

suitable for your socket, then

the plug should be cut off and

an appropriate plug fitted.

Destroy the old plug, which is

cut off as a plug with a bared

cord could cause a shock

hazard if inserted into a socket

elsewhere in the house.

The moulded plug on this

appliance incorporates a 13A

fuse. Should the fuse need to

be replaced an ASTA approved

BS1362 fuse of the same rating

must be used. Do not forget

to refit the fuse cover. In the

event of losing the fuse cover,

the plug must not be used

until a replacement fuse cover

has been fitted. Colour of the

replacement fuse cover must

be the same colour as that

visible on the pin face of the

plug. Fuse covers are available

from any good electrical store.

Fitting a different plug

As the colours of the wires in the mains

lead of this appliance may not correspond

Содержание din28r20














































Результаты поиска

Содержание din28r20

Отзывы:

Похожие инструкции для din28r20

Бренды по названию

Популярные бренды

Beko din28r20, Руководство пользователя

Результаты поиска

Содержание din28r20

Отзывы:

Похожие инструкции для din28r20

Бренды по названию

Популярные бренды