
63
APPENDIX 4
BA334E Rate Totaliser
The BA334E Rate Totaliser is functionally identical
to the BA334G Rate Totalisers described in the main
sections of this manual, but differs in mechanical
construction, certification and factory fitted options.
All BA334E Rate Totalisers are fitted with:
A Green internally powered display backlight
Dual galvanically isolated alarms
An isolated 4/20mA current sink output
These are only available as factory fited options for
the BA334G Rate Totaliser.
A4.1 Mechanical construction
The BA334E is housed in a robust GRP IP66
enclosure with a separate terminal compartment.
Section A4.5 of this appendix describes the
enclosure and installation procedure.
A4.2 Certification
The BA334E has the same ATEX, IECEx and ETL
intrinsic safety certification as the BA334G, but the
BA334E does not have ATEX and IECEx dust
certification
.
The safety parameters and certification numbers
specified in this manual for the BA334G Rate
Totalisers also apply to the BA334E Rate Totaliser.
Therefore all of the systems described for the
BA334G in the main section of this manual may also
be used for the BA334E.
A4.3 Location
The BA334E Rate Totaliser is housed in a robust
IP66 glass reinforced polyester (GRP) enclosure
incorporating an armoured glass window and
stainless steel fittings. It is suitable for exterior
mounting in most industrial installations, including
off-shore and waste water treatment sites. The Rate
Totaliser should be positioned where the display is
not in continuous direct sunlight.
The field terminals and the two mounting holes are
located in a separate compartment with a sealed
cover allowing the instrument to be installed without
exposing the display assembly.
The enclosure is fitted with a bonding plate to
ensure electrical continuity between the three
conduit / cable entries.
A4.4 BA334E Accessories
A4.4.1 Units measurement & instrument
identification.
The BA334E is fitted with a blank escutcheon
around the liquid crystal display. This can be
supplied printed with any units of measurement
and tag information specified at the time of
ordering. Alternatively, the information may be
added on-site via an embossed strip, dry transfer
or a permanent marker.
To gain access to the escutcheon remove the
terminal cover by unscrewing the two 'A' screws
which will reveal two concealed 'D' screws.
Remove the push buttons by unscrewing the two
'C' screws and un-plug the five way connector.
Finally, unscrew all four 'D' screws and carefully lift
off the front of the instrument. The location of all
the screws is shown in Fig A4.1.
Add the required legend to the display escutcheon,
or stick a new pre-printed self-adhesive
escutcheon, which is available from BEKA
associates, on top of the existing escutcheon. Do
not remove the original escutcheon.
The BA334E can also be supplied with a blank or
custom laser engraved stainless steel plate
secured by two screws to the front of the
instrument enclosure. This plate can typically
accommodate:
1 row of 9 alphanumeric characters 10mm high
or 1 row of 11 alphanumeric characters 7mm high
or 2 rows of 18 alphanumeric characters 5mm
high.
A4.4.2 Pipe mounting kits
The BA334E Rate Totaliser is surface mounting,
but may be pipe mounted using the BA392D or the
BA393 pipe mounting kit.
Содержание BA334E
