manualshive.com logo in svg

Beiyuan BQS-1H, Инструкция по эксплуатации

Поделиться
Скачать
Beiyuan BQS-1H Скачать руководство пользователя страница 8

Page 

8

 of 

17

 

 

IV. Operation 

 

4.1 Pre-work inspection and preparation 

(1) Check that the comb and cutter are properly installed, and tension is correct.  
(2) Check if the gearbox has been greased as required, other lubricated parts have 
been greased as required. 
(3) Check if the voltage of the main power supply and the special power supply 
(Controller) for the handpiece is correct. 
 

4.2 Pre-use and in-use safety and precautions 

(1)

 

The power outlet must be reliably grounded. 

(2)

 

Before turning on the power, the switche on the handpiece must be set to OFF. 

(3) After the power is connected, with the handpiece in hand, turn on the switch at 
the back of the handpiece. 
(4) During shearing, the cutting head of the handpiece should always maintain a safe 
distance from the operator. 
(5) During shearing, the lead of the handpiece should be kept free and unobstructed 
to avoid tangling with sheep. 
(6) While on break, the handpiece should be turned off to prolong its service life. 
(7) Keep the vents of the handpiece motor free from blockage, any wool or debris 
blocking the vents should be promptly removed. 
(8) If a problem occurs during shearing, first shut off the handpiece and cut off the 
power supply, then proceed to perform inspection and maintenance. 
(9) Ensure the handpiece is turned off and the power is cut off before loosening the 
tension nut. 
(10) Do not turn on the handpiece without first installing the comb and cutter. 
 

Caution: power must be completely unplugged before performing maintenance 
on the handpiece! 
 

4.3 Using the handpiece 

(1) Plug in the power cord into the power supply and ensure it is secure. 
(2) Hang or fix the control box at a height of approximately 1.4 

– 1.7 meters above 

ground. 
(3) Connect the control box to the main power supply with its 3 points plug. 
(4) To start or halt operation, use the switch located at the back of the handpiece. 
 

Caution: the handpiece must be started under zero load before every 
operation. 
 
 

Содержание BQS-1H


















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды